manualshive.com logo in svg

Johnson Controls LN-DSWSC1-0, Руководство по установке, Страница: 4 / 8

Поделиться
Скачать
Johnson Controls LN-DSWSC1-0 Скачать руководство пользователя страница 4

LN-Display Installation Instructions

4

6.

Connect the power and network communication 
wires. See the 

Wiring

 section for more information.

7.

Reattach the front panel to the base plate by 
pressing gently on the Display until the panel clicks 
into place.

Flush Mount Casing

To mount the LN-Display with flush mount casing:

1.

Remove the Display panel from the device by 
gently pressing outwards on the rear openings 
(Figure 7). 

2.

Create a 4 1/2 x 4 1/2 in. (113 x 133 mm) opening 
in the enclosure cover, if necessary (Figure 8).

Note:

See Figure 2 for the controller dimensions.

3.

Position the Display in the opening of the enclosure 
cover and then transfer the position of the four 
mounting holes to the cover (Figure 9).

4.

Remove the Display front panel from the enclosure 
cover and drill the four holes.

5.

Fasten the enclosure cover on the panel.

6.

Pull the power and network communication wires 
through the wire exit hole.

7.

Connect power and network communication wires.

8.

Reattach the front panel to the base plate by 
pressing gently on the display until the panel clicks 
into place. 

Location Considerations

For proper installation and subsequent operation of the 
Display controller, follow these recommendations:

•

Allow for proper clearance of device casing, wiring 
terminals, and service pin for easy access, 
hardware configuration, and maintenance.

•

Record the Neuron® ID number located on the 
inside of the device casing for commissioning the 
device.

•

Install at the following environmental conditions:
Ambient temperature: 32 to 158°F (0 to 70°C)
Relative humidity: 0 to 95%, noncondensing

•

Ensure proper ventilation of devices, and avoid 
area where corroding, deteriorating, or explosive 
vapors, fumes, or gasses may be present.

Wiring

Power Wiring

LN-Display device power requirements: 24 VAC/VDC, 
±15%, Class 2. Use transformers of 100 VA or less.

Figure 7: Remove Flush Mount 

Casing

Figure 8: Enclosure

 

IMPORTANT:

Make all wiring connections in 

accordance with local, national, and regional 
regulations. Do not exceed the LN-Display’s 
electrical rating.

Figure 9: Mounting Holes for Flush 

Mount Casing

 

1

1. Mounting holes for flush mount casing

1

1

1

Содержание LN-DSWSC1-0









Отзывы:

Нет отзывов