Johnson Controls G861 Series Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 12

Johnson Controls G861 Series Скачать руководство пользователя страница 7

G—G861 Series Integrated Function Direct Spark Ignition Control Technical Bulletin 7

IMPORTANT:

This technical bulletin is intended as a guide for
qualified personnel installing or servicing
Johnson Controls products. Carefully follow all
instructions in this sheet and all instruction on the
appliance. Limit repairs, adjustments, and servicing
to the operations listed in this sheet or on the
appliance.

!

WARNING:

Fire or Explosion Hazard. Avoid serious injury by
carefully following precautions in this sheet and all
instructions on the appliance. Limit repairs,
adjustments, and servicing to the operations listed in
this sheet or on the appliance.

!

WARNING:

Fire or Explosion Hazard. If the control is
installed in an area that is exposed to water
(dripping, spraying, rain, etc.), it must be protected.
If the control has been exposed to water in any way,
do not use it.

!

WARNING:

Shock Hazard. Avoid electrical shock and
equipment damage. Disconnect the electrical
power and turn off the gas before wiring the
control into the circuit.

Choose a location that provides the shortest, direct cable route to the spark
igniter and flame sensor. Easy access to the terminals is desired for wiring
and servicing. The G861 may be mounted in any position. Mount the
control on a grounded metal surface with No. 8 machine or No. 6 sheet
metal screws.

!

CAUTION:

Equipment Damage Hazard. Do not mount the
control where it will be exposed to direct infrared
radiation from the main burner or to temperatures in
excess of the maximum product temperature rating.

Installation and
Wiring

Mounting

«
...
5
6
7
8
9
...
»

Содержание G861 Series













Отзывы:

Нет отзывов