Johnson Controls G861 Series Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 12

Johnson Controls G861 Series Скачать руководство пользователя страница 5

G—G861 Series Integrated Function Direct Spark Ignition Control Technical Bulletin 5

Upon receiving a call for continuous manual fan, the G861 energizes the
circulator/blower motor at medium fan speed. The continuous fan on
request is immediately overridden by a call for heat.

The G861 offers the following responses based on abnormal system
operation.

A pressure switch within the appliance provides proof of combustion air
flow. During a heating cycle, the G861 control responds to the state of this
switch in the following ways:

•

At the beginning of the heating cycle, if the pressure switch is not open
before the inducer is energized, the control will wait for the switch to
open for as long as the call for heat is present. The G861 control LED
(Light-Emitting Diode) will blink with a flash code of 3 while waiting
for the pressure switch to open.

•

If the pressure switch does not close after the inducer has been
energized for 8 seconds, the control will keep the inducer energized and
the LED will blink with a flash code of 3 until the pressure switch
closes or the call for heat is removed.

•

If the pressure switch opens any time after the G861 control has begun
the trial for ignition, the control will immediately de-energize the gas
valve. If the pressure switch fault occurs after the flame is sensed, the
circulator/blower will run for 90 seconds, the inducer motor will remain
energized, and the control will go into the Pressure Switch Open Fault
state. During this time, the LED will blink with a flash code of 3. As
long as the call for heat is still present, the control will continue to wait
for the pressure switch to close before resuming the heating cycle. If the
pressure switch fails three times with no more than 30 seconds between
successive faults, the control will go to PSWFLT1 and PSWFLT 2 state
with an LED flash code of 3.

If a flame is present at power up, the G861 allows the flame to extinguish
within 10 seconds. If this occurs, the normal sequence of operation
continues. If the flame is still present after 10 seconds, the G861 goes into
flame lockout. If flame is present any other time it should not be, the G861
goes into flame lockout after a 10-second delay.

During the flame lockout, the inducer motor and the circulator/blower
remain energized, and the main valve is de-energized. The G861 control
LED flashes with a duty cycle of 1/2 second On, 1/2 second Off for
five flashes with a longer Off time before repeating the series. The control
remains in this state until the main power is cycled.

Call for Manual
Fan

Abnormal
System
Operation

Pressure Switch
Detection

Undesired Flame

«
...
3
4
5
6
7
...
»

Содержание G861 Series













Отзывы:

Нет отзывов