Johnson Controls G770BGJ Скачать руководство пользователя страница 1 | Manualshive

Страница: 1 / 16

background image

Installation Sheets Manual

121

Gas Combustion Combination Controls and Systems

G

Technical Bulletin

G770

Issue Date

0498

©

1998 Johnson Controls, Inc.

1

Part No. 24-8143-596, Rev.



Code No. LIT-121253

Figure 1: G770BGJ 100% Lockout,

Microprocessor-Based IPI Control

The G770BGJ is a member of the G700 series ignition control family.
This Intermittent Pilot Ignition (IPI) control is microprocessor-based and
provides two additional trials if the supervised pilot flame is not proven
within the initial trial for ignition period. A diagnostic LED (Light-
Emitting Diode) indicates operating status and assists in system
troubleshooting.

The microprocessor provides improved reliability and performance. All
function timings are independent of voltage and temperature variations.
The control is monitored on a cycle-by-cycle basis for maximum
operational integrity.

G770BGJ 100% Lockout, Microprocessor-Based

Intermittent Pilot Ignition Control

Description

1
2
3
...
»

Содержание G770BGJ

















Отзывы:

Нет отзывов

Похожие инструкции для G770BGJ

Бренд: Federal Signal Corporation Страницы: 60

Бренд: FASTRON. Страницы: 16

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

PXI-6683 Series

Бренд: National Instruments Страницы: 4

Бренд: National Instruments Страницы: 9

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 29

Бренд: National Instruments Страницы: 11

Бренд: National Instruments Страницы: 7

FIELDPOINT FP-1600

Бренд: National Instruments Страницы: 21

FieldPoint FP-1001

Бренд: National Instruments Страницы: 65

FieldPoint FP-1001

Бренд: National Instruments Страницы: 19

Бренд: National Instruments Страницы: 16

Бренд: National Instruments Страницы: 10

Бренд: Oceanic Страницы: 11

Бренд: Olsberg Страницы: 68

Бренд: Paradox Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды