background image

Troubleshooting the Controllers

Observe the Status LEDs on the front of the controller
and see

Table 8

to troubleshoot the controller.

Table 8: Status LEDs and Descriptions of LED States

Description of LED States

Normal LED
State

LED Color

LED Label

Off Steady = No Supply Power or the controller’s polyswitch/resettable fuse
is open. Check Output wiring for short circuits and cycle power to controller.

On Steady = Power Connected

On Steady

Green

POWER

Off Steady = No Faults

On Steady = Device Fault; no application loaded; Main Code download
required, if controller is in Boot mode, or a firmware mismatch exists between
the controller and the FX-ZFR1811 Wireless Field Bus Router.

Blink - 2 Hz = Download or Startup in progress, not ready for normal operation

Off Steady

Red

FAULT

Blink - 2 Hz = Data Transmission (normal communication)

Off Steady = No Data Transmission (N/A - auto baud not supported)

On Steady = Communication lost, waiting to join communication ring

Blink - 2 Hz

Green

SA/FC BUS

On Steady = EOL switch in ON position

Off Steady = EOL switch in Off position

Off (Except on
terminating
devices)

Amber

EOL

Repair Information

If a controller fails to operate within its specifications,
replace the controller. For a replacement controller,
contact your Johnson Controls

®

representative.

Accessories

See

Table 9

for controller accessories ordering

information.

Table 9: Accessories Ordering Information

Description

Product Code Number

Bluetooth Commissioning Converter

FX-BTCVT-1

Wireless Field Bus Router

FX- ZFR1811-0

Transformer, 120 VAC Primary to 24 VAC secondary, 20 VA, Wall Plug

TP-2420

Transformer, 120/208/240 VAC Primary to 24 VAC Secondary, 40 VA, Foot Mount, 8 in.
Primary Leads and Secondary Screw Terminals, Class 2

Note:

Additional Y6x-x Series transformers are also available. Refer to the

Series Y63, Y64,

Y65, Y66, and Y69 Transformers Product Bulletin (LIT-125755)

for more information.

Y65T31-0

Power transformer (Class 2, 24 VAC, 50 VA maximum output), no enclosure

AS-XFR050-0

Replacement SA/FC Bus Terminal Blocks, 4-Position, Gray, Bulk Pack of 10

Note:

This is the standard terminal block that is provided with the controller.

MS-TBK4BUS-0

Replacement SA Bus Terminal Blocks, 4-Position, Brown, Bulk Pack of 10

Note:

These terminal blocks can be used as replacement parts if keeping consistent terminal

block colors is important.

AP-TBK4SA-0

Replacement FC Bus Terminal Blocks, 4-Position, Blue, Bulk Pack of 10

Note:

These terminal blocks can be used as replacement parts if keeping consistent terminal

block colors is important.

AP-TBK4FC-0

19

FX-PCX47 Expansion Input/Output Module Installation Instructions

Содержание FX-PCX47























Отзывы: