manualshive.com logo in svg

Johnson Controls Frick PowerPac, Установка, эксплуатация и обслуживание

Поделиться
Скачать
Johnson Controls Frick PowerPac Скачать руководство пользователя страница 16

FRICK

®

 POWERPAC

™

SAFETY

170.600-IOM (JUN 11)

Page 16

When halocarbon vapors come into contact with open flame 
or hot surfaces 

over approximately 572°F (300°C

) they de-

compose to produce poisonous chemicals. These chemicals 
have a very strong odor warning us of their presence.

Oil mist in the ammonia vapor increases this risk significantly 
as the point of ignition falls below that of the mixture ratio 
stated.

Usually the strong smell of ammonia will give ample warning 
of its presence before concentrations become dangerous.

Check official limits in the location 
of your installation. They may differ 
from those stated.

VENTILATING A REFRIGERATION PLANT

If it is necessary to ventilate a refrigeration plant, make sure 
you observe the following:
• 

Never

 release refrigerants directly into the atmosphere.

•  When ventilating an R-717 plant, you must use an ap-

proved air ventilator. 

Released air must pass through 

an open water

 container in which the remnants of R-717 

refrigerant will be absorbed. Send the water containing 
R-717 to an authorized incineration plant. 

COOLING AGENTS

Standard  PowerPac

™

  units  are  designed  to  use  glycol  or 

water as the cooling agent. Other cooling agents include: 
Salt solutions (brines) of calcium chloride (CaCl

2

) or sodium 

chloride (NaCl).

In general, all brines must be considered harmful to nature. 
Use caution when charging or purging a refrigeration plant. 

Never empty brines down a sewer or into the environment. 

The brine must be collected in suitable containers, clearly 
marked with the contents, and sent to an approved incin-
eration plant.

OILS

To lubricate screw compressors included in the PowerPac

™

 

units, use only Semisynthetic hydrotreated oil.

When changing the oil in the compressors and when empty-
ing the vessels, the used oil must be charged into containers 
marked  “waste  oil”  and  sent  to  an  approved  incineration 
plant.

NOTE: The owner of the refrigeration plant is responsible 
for ensuring compliance with all Federal, state, and local 
regulations. PSM procedures should be routinely followed.

Содержание Frick PowerPac

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды