manualshive.com logo in svg

Johnson Controls FMS-1655M, Руководство по установке, Страница: 13 / 23

Поделиться
Скачать
Johnson Controls FMS-1655M Скачать руководство пользователя страница 13

FMS-1655M

LIT-12013119

13

+ (RS485) - (RS485) GND IN +Vs Io Vo - V

in

+Vi

n

+ (RS485) - (RS485) GND IN +Vs Io Vo - V

in

+Vi

n

Installation detail view

Remote Sensor Installation Detail

(Bottom View)

Isolation Room

Corridor

Stainless Steel 

Mounting Plate

Gasket

Louvered Cover 

Plate

Stainless Steel 

Flow Tube 

Mounting Plate

Gasket

Thin Silicone Caulking 

(apply around tube and 

between stainless steel 

plate and wall to seal 

unit penetration)

Terminal

For connection of 

transmitter to  

FMS-1655M Monitor. 

Flow Tube

When Flow Tube 

mounting plate is located 

directly opposite the 

sensor, flow tubing 

must be cut as short as 

possible to prevent kinks.

To FMS-1655M Monitor  

monitor

Wall Section

(cutaway view)

Rotating clamps secure 

assembly to wall board

Optional Analog 

Output Damper 

Control

To Johnson Controls  

isolation transformer

To optional  

door switch

Note: 

To maintain sensor 

accuracy, Flow tube 

should not exceed 36 

inches.

Содержание FMS-1655M
























Отзывы:

Нет отзывов