background image

1

FMS-1655M

Room Pressure Monitor

LIT-12013119

January 2019

Installation Instructions

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC 

Rules. These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a 

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in 

accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a 

residential area may cause harmful interference, in which case users will be required to correct the interference at their own expense.

Application

These installation instructions guide the installer through the installation of the FMS-1655M Room Pressure Monitor.

Please read these instructions thoroughly before beginning installation.

North American Emissions Compliance

United States

Canada

Installation

This Class (A) digital apparatus meets all the requirements of the Canadian Interference-Causing Equipment Regulations.

Cet appareil numérique de la Classe (A) respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada.

IMPORTANT

The FMS-1655M Room Pressure Monitor must be wired to 24 VAC only. Wiring the unit to 110 VAC will cause 

serious damange and void the warranty. 

Risk of Property Damage.

 

Ensure that the power source conforms to the requirements of the equipment. Failure to use a correct power source may result in 

permanent damage to the equipment.

Risque de dégâts matériels.

 

S’assurer que la source d’alimentation électrique est conforme aux spécifications de l’équipement. L’utilisation d’une source 

d’alimentation électrique inappropriée risque d’endommager irrémédiablement l’équipement.

NOTICE

NOTICE

Use of the software that is in (or constitutes) this product or access to the cloud or hosted services applicable to this product, if any, 

is subject to applicable terms set forth at www.johnsoncontrols.com/techterms.  Your use of this product constitutes an agreement to 

such terms.  If you do not agree to be bound by such terms, you may return the unused product to your place of purchase.

LB-FMS1655M-S01

LB-FMS1655M-T01

Содержание FMS-1655M
























Отзывы: