Johnson Controls FCP-NA-701-L Скачать руководство пользователя страница 25

Страница: 25 / 28

Table 9: Fault list

Error code

Description

Solutions

ER:05

ERROR_REMOTE_SENSOR_OPEN

•

Verify if the remote temperature sensor is

disconnected from the thermostat terminals

RS and SC. If yes, re-wire the remote

sensor correctly and then power cycle the

thermostat.

•

Verify if the remote sensor is malfunctioned

or damaged.

•

Contact technical support.

ER:06

ERROR_REMOTE_SENSOR_SHORT

•

Verify the remote temperature sensor

wiring and check if thermostat terminals

RS and SC are shorted. If yes, re-wire the

remote sensor correctly and then power

cycle the thermostat.

•

Verify if the remote sensor is malfunctioned

or damaged.

•

Contact technical support.

ER:07

ERROR_REMOTE_SENSOR_HI

Remote sensor detected a too high temperature.

•

Check if the thermostat wiring is connected

correctly to the FCU or PTAC.

•

Verify if the remote sensor is installed

correctly in the room or duct.

•

Contact technical support.

ER:08

ERROR_REMOTE_SENSOR_LO

Remote sensor detected a too low temperature.

•

Check if the thermostat wiring is connected

correctly to the FCU or PTAC.

•

Verify if the remote sensor is installed

correctly in the room or duct.

•

Contact technical support.

ER:09

ERROR_PIPE_SENSOR_OPEN

•

Check if the pipe temperature sensor

wiring is disconnected from thermostat

terminals PS and SC. If yes, re-wire the pipe

sensor correctly and then power cycle the

thermostat.

•

Verify if the pipe sensor is malfunctioned or

damaged.

•

Contact technical support.

ER:10

ERROR_PIPE_SENSOR_SHORT

•

Verify the pipe temperature sensor wiring

and check if thermostat terminals PS and

SC are shorted. If yes, re-wire the pipe

sensor correctly and then power cycle the

thermostat.

•

Verify if the pipe sensor is malfunctioned or

damaged.

•

Contact technical support.

ER:11

ERROR_PIPE_SENSOR_HI

Pipe sensor detected a too high temperature.

•

Verify if the pipe sensor is installed correctly

in the pipe.

•

Contact technical support.

ER:12

ERROR_PIPE_SENSOR_LO

Pipe sensor detected a too low temperature.

•

Verify if the pipe sensor is installed correctly

in the pipe.

•

Contact technical support.

FCP Non-Programmable and Programmable Fan Coil or PTAC Thermostat Largo User Guide

Содержание FCP-NA-701-L




























Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды

Johnson Controls FCP-NA-701-L, Руководство пользователя

Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды