Johnson Controls FCP-NA-701-L Скачать руководство пользователя страница 18

Страница: 18 / 28

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to IS, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 53.

5. Use the

and

Down

buttons to set smart auto fan to On or Off and press

Mode

to confirm

the change.

Fan mode reset

The fan mode reset function resets the fan mode to Auto after the fan mode reset time elapsed.

You can set the fan mode reset time to 2 hours, 4 hours, and 24 hours. By default, the fan mode

reset time is set to Off. To set the fan mode reset time, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to IS, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 54.

5. Use the

and

Down

buttons to set the fan mode reset time and press

Mode

to confirm the

change.

Fan delay

Fan delay is a time delay for the fan terminal to turn off after the heating or cooling terminal turned

off. The fan delay is available when the fan mode is Auto. You can set a delay between 0 seconds

and 10 seconds. To set the fan delay, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to IS, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 56.

5. Use the

and

Down

buttons to set the fan delay time and press

Mode

to confirm the

change.

Programmable mode (FCP-PA only)

The programmable mode is available on the FCP-PA model only. With the programmable mode you

can set a heat and cool schedule for up to seven consecutive days and each day can consist of up

to six periods. You can change the start times of each period by increments of 15 minutes. You can

also set the time and date in the programmabe mode.

Enabling the programmable mode

To enable the programmable mode, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to UP, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 10.

5. Use the

and

Down

buttons to set the programmable mode to ON and press

Mode

confirm the change.

FCP Non-Programmable and Programmable Fan Coil or PTAC Thermostat Largo User Guide

Содержание FCP-NA-701-L




























Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды

Johnson Controls FCP-NA-701-L, Руководство пользователя

Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды