Johnson Controls FCP-NA-701-L Скачать руководство пользователя страница 23

Страница: 23 / 28

6. Press

Mode

to confirm the change.

Result

The thermostat calculates the difference between the current measured temperature

and the user set current temperature to determine the calibration offset. Calibration changes the

temperature as part of measurement and scaling. The thermostat uses the calibrated temperature

as true reference to determine the pipe water temperature and the pipe state.

The default calibration offset value is 0.

Note:

The pipe sensor calibration menu option is visible only when the pipe sensor temperature

reading is ready.

Adjusting the backlight

About this task:

You can adjust the length of time that the backlight stays on and the brightness

of the backlight.

To adjust the length of time that the backlight stays on, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to UP, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 05.

5. Use the

and

Down

buttons to change the backlight on duration, then press

Mode

confirm the change.

To adjust the backlight brightness, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to UP, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 06.

5. Use the

and

Down

buttons to change the backlight brightness level, then press

Mode

confirm the change.

Setting the displayed temperature

You can choose to display the ambient temperature, set temperature, or both. To set the displayed

temperature, complete the following steps:

1. Press

Mode

to set the thermostat to OFF mode.

2. Press and hold

Mode

and

Fan

for 5 seconds to access the advanced settings menu.

3. Press

to navigate to UP, then press

Mode

to enter the menu.

4. Press

Mode

to navigate to 07.

5. Use the

and

Down

buttons to change the displayed temperature.

- Select 0 to display the ambient temperature and the set temperature.
- Select 1 to display the set temperature.
- Select 2 to display the ambient temperature.

6. Press

Mode

to confirm the change.

FCP Non-Programmable and Programmable Fan Coil or PTAC Thermostat Largo User Guide

Содержание FCP-NA-701-L




























Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды

Johnson Controls FCP-NA-701-L, Руководство пользователя

Результаты поиска

Содержание FCP-NA-701-L

Отзывы:

Похожие инструкции для FCP-NA-701-L

Бренды по названию

Популярные бренды