manualshive.com logo in svg

Johnson Controls FAC2611-0U, Руководство по установке, Страница: 25 / 25

Поделиться
Скачать
Johnson Controls FAC2611-0U Скачать руководство пользователя страница 25

Table 10: FAC2611-0U Field Application Controller

United States:

UL Listed, File E107041, CCN PAZX, UL 916, Energy Management

Equipment; FCC Compliant to CFR47, Part 15, Subpart B, Class A

UL Listed, File S4977, UL 864 UUKL/UUKLC 10th Edition Listed, Smoke Control
Units and Accessories for Fire Alarm Systems Equipment

Compliance

Canada:

UL Listed, File E107041, CCN PAZX7 CAN/CSA C22.2 No.205, Signal

Equipment; Industry Canada Compliant, ICES-003

UL Listed, File S4977, UL 864 UUKL/ORD-C100-13 10th Edition Listed, Smoke
Control Units and Accessories for Fire Alarm Systems

Europe:

Johnson Controls declares that this product is in compliance with the

essential requirements and other relevant provisions of the EMC Directive.

Australia and New Zealand:

RCM Mark, Australia/NZ Emissions Compliant

BACnet International:

BACnet Testing Laboratories (BTL) Protocol Revision 7

Listed BACnet Advanced Application Specific Controller (B-ASC)

The performance specifications are nominal and conform to acceptable industry standard. For application at conditions
beyond these specifications, consult the local Johnson Controls

®

office. Johnson Controls shall not be liable for

damages resulting from misapplication or misuse of its products.

APAC Single Point of Contact:

NA/SA Single Point of Contact:

European Single Point of Contact:

JOHNSON CONTROLS

C/O CONTROLS PRODUCT MANAGEMENT

NO. 22 BLOCK D NEW DISTRICT

WUXI JIANGSU PROVINCE 214142

CHINA

JOHNSON CONTROLS

507 E MICHIGAN ST

MILWAUKEE WI 53202

USA

JOHNSON CONTROLS

WESTENDHOF 3

45143 ESSEN

GERMANY

Building Technologies & Solutions

507 E. Michigan Street, Milwaukee, WI 53202

Metasys

®

and Johnson Controls

®

are registered trademarks of Johnson Controls.

All other marks herein are the marks of their respective owners.

©

2018 Johnson Controls

www.johnsoncontrols.com

Published in U.S.A.

25

FAC2611-0U Advanced Application Field Equipment Controller Installation Instructions

Содержание FAC2611-0U


























Отзывы:

Нет отзывов