Johnson Controls FAC2611-0U Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 25

Johnson Controls FAC2611-0U Скачать руководство пользователя страница 13

Terminal Wiring Guidelines,
Functions, Ratings, and
Requirements

Input and Output Wiring Guidelines

provides information and guidelines about the

functions, ratings, and requirements for the controller
input and output terminals; and references guidelines for
determining proper wire sizes and cable lengths.

In addition to the wiring guidelines in

, observe

these guidelines when wiring controller inputs and
outputs:

•

Run all low-voltage wiring and cables separate from
high-voltage wiring.

•

All input and output cables, regardless of wire size or
number of wires, should consist of stranded, insulated,
and twisted copper wires.

•

Shielded cable is not required for input or output
cables.

•

Shielded cable is recommended for input and output
cables that are exposed to high electromagnetic or
radio frequency noise.

•

Inputs/outputs with cables less than 30 m (100 ft)
typically do not require an offset in the software setup.
Cable runs over 30 m (100 ft) may require an offset
in the input/output software setup.

Table 3: FAC2611 Terminal Blocks, Functions, Ratings, Requirements, and Cables

Determine Wire Size and
Maximum Cable Length

Function, Ratings, Requirements

Terminal
Label

Terminal Block
Label

Same as (Universal)

INn

Note:

Use 3-wire cable for
devices that source
power from the +15V
terminal.

15 VDC Power Source

for active (3-wire) input devices

connected to the Universal IN

n

terminals.

Provides 100 mA total current

+15 V

UNIVERSAL

(Inputs)

See Guideline

A

in

Analog Input - Voltage Mode (0–10 VDC)

10 VDC maximum input voltage

Internal 75k ohm Pull-down

INn

See Guideline

B

in

Analog Input - Current Mode (4–20 mA)

Internal 100 ohm load impedance

Note:

Current loop jumpers are fail-safe to maintain a
closed 4 to 20 mA current loop, even when the
power to the controller is interrupted or off. See

Current Loop Jumpers

.

See Guideline

A

in

Analog Input - Resistive Mode (0–600k ohm)

Internal 12 V. 15k ohm pull up

Qualified Sensors: 0-2k ohm potentiometer, RTD (1k Nickel
[Johnson Controls

®

sensor], 1k Platinum, and A99B Silicon

Temperature Sensor) Negative Temperature Coefficient
(NTC) Sensor

See Guideline

A

in

Binary Input - Dry Contact Maintained Mode

1 second minimum pulse width

Internal 12 V. 15k ohm pull up

Same as (Universal)

INn

Universal Input Common

for all Universal Input terminals

Note:

All Universal ICOM

n

terminals share a common,

which is isolated from all other commons.

ICOMn

13

FAC2611-0U Advanced Application Field Equipment Controller Installation Instructions

«
...
11
12
13
14
15
...
»

Содержание FAC2611-0U


























Отзывы:

Нет отзывов