Johnson Controls Bentel Security tyco ABS128M50, Руководство по установке

Страница: 122 / 132

Reporting Formats
This paragraph describes the structures of the main re-
porting formats supported by the system.
+
Installer should customize codes for Superkey ac-
cording to customer (f.e. 1: Emergency, 2: Fire, 3:
Alarm). 000 means NO Communicate.
n
Contact ID
Contact ID transmits as follows.
Ø
User Code (4 hexadecimal digits — 0 through F ).
Ø
Qualifier: 1 = new event or Disarming operation; 3
restore event or Arming operation.
Ø
Class Code ( CL. column): identifies the type of
event (Alarm, Trouble, Fire, etc.).
Ø
Reporting Code ( CODE column): identifies the
event (Reporting Codes can be changed, refer to
“Events and Actions” in the “PROGRAMMING
FROM THE PC” section).
+
00 means NO communication.
Ø
Group Number ( GROUP column), where possible,
identifies the Partition of the “resource” which gener-
ated the event.
Ø
Zone Number ( ZONE column), where possible,
identifies the “resource” (Zone, Code, Key, etc.)
which generated the event.
n
SIA
SIA is a FSK (Frequency Shift Keying) format, that trans-
mits alternatively in two slightly different frequencies.
The frequency shift is usually 170 Hertz, and the two fre-
quencies are associated with 0 and 1 of the binary digit
which transmits the following data:
Ø
User Code (4 digits — 0 through 9)
Ø
Function Code (1 digit; N=new event, O=restore event)
Ø
Date (month-day-year)
Ø
Time (hour-minutes-seconds)
Ø
Event Type (refer to the TYPE column in Table 22)
Ø
Event Agent (refer to the 1
st
and 2
nd
columns in Ta-
ble 22).
122 Expandable Hybrid Control Panel
EVENT CONTACT ID SIA
CL.CODE GROUP ZONE TYPE 1
st
2
nd
Alarm on zone 1 30 00 Zone n. BA/BR 0000 Zone n.
Tamper on zone 1 37 00 Zone n. TA/TR 0000 Zone n.
Fire alarm on partition 1 10 Part. n. 000 FA/FH Part. n. 000
Low Battery on Wireless Detector 3 84 00 Detector n. XT/XR 0000 Detector n.
Partial arming partition 4 41 Part. n.
30
NL/OP part. n.
30
Generic alarm on partition 1 30 Part. n. 000 BA/BH part. n. 000
Tamper alarm on partition 1 37 Part. n. 000 TA/TR part. n. 000
Global arming partition 4 00 Part. n.
30
CL/OP part. n.
30
Disarming partition 4 00 Part. n.
30
OP/CL part. n.
30
keyfob low battery 3 38 00 Keyfob n. XT/XR 0000 Keyfob n.
Tamper on Main unit 1 37 00 000 TA/TR 0000 000
Service jumper 0 00 00 000 00/00 0000 000
Tamper on external siren 1 37 00 000 TA/TR 0000 000
Tamper on internal siren 1 37 00 000 TA/TR 0000 000
Tamper on Main unit (seize) 1 37 00 000 TA/TR 0000 000
Warning BPI peripheral 3 33 00 000 EM/EN 0000 000
Balanced tamper 1 37 00 000 TA/TR 0000 000
Warning fuse 3 00 00 000 YP/YQ 0000 000
Tamper BPI device 1 45 00 000 ES/EJ 0000 000
Schedule on Partition 0 00 00 000 00/00 0000 000
Wireless zone loss on Panel 3 81 00 000 BS/BR 0000 000
Wireless Receiver Tamper 1 45 00 000 ES/EJ 0000 000
Zone alarm on Panel 1 30 00 000 BA/BH 0000 000
Zone tamper on Panel 1 37 00 000 TA/TR 0000 000
System fault 3 00 00 000 BT/BJ 0000 000
Table 22 Structure of the main Reporting formats supported by the System (continued ...).
30 Transmits: 000 for the operation performed by the Command Zones and the Scheduler; the Identification Num-
ber of the PIN which produced the event (from 001 to 128 ); the Identification Number, increased by 128 units, of the
Digital Key which produced the event (from 129 to 378 ); the Identification Number, increased by 128 + 250 units, of
the keyfob which produced the event (from 379 to 394 ). For example, if the event was produced by PIN no.1, 001 is
transmitted; if the event was produced by Digital Key no.1, 129 (1 + 128) is transmitted.