Johnson & Starley JANSTAR Скачать руководство пользователя страница 1

JANSTAR

MODULATING WARM AIR HEATER

with SYSTEM E-T Control

INSTALLATION, COMMISSIONING & SERVICING INSTRUCTIONS

G.C. No 42 451 07

Publication No. ZZ 757/9

June 2000

Fig. 1

JANSTAR Principal Components

1.1

The Johnson & Starley JANSTAR is a all mounted, room sealed, fan assisted, down flow warm air heater with SYSTEM
E-T control. It is designed for use with a concentric air inlet/flue, which enables combustion air to be admitted to the
burner, whilst combustion products are discharged to the outside, via a concentric terminal.

1.2

The air heater output varies automatically between 8.0 kW (27,300Btu/h) and 2.0 kW (6,800 Btu/h) for horizontal flued
installations, and 8.5 kW (29000Btu/h) and 2.8 kW (9600Btu/h) for vertical flued installations.

1.3

The appliance is supplied assembled for left hand return air entry. For conversion to right hand return entry, refer to
Section 4. If return air is via the top of the fan chamber, a side blanking plate (Pt No W800-0133000) is required. An
adaptor kit is available which permits the appliance to be converted to an upflow model. The appliance may be base duct
mounted. The JANSTAR is also provided with the facility for connection to a remote time control (not supplied), with
volt-free contacts (i.e. The switching supply is provided by JANSTAR), to enable selection of operating times.

1.4

A mesh filter, for air return duct mounting, is supplied as standard. However, a Cleanflow electronic filter is offered as an
alternative option.

THIS APPLIANCE CONFORMS TO BS EN 55014

Key

Description

Key

Description

  1

Air circulating fan

  7

Fan delay/ Overheat limit control

  2

Fan energy capacitor

  8

Air filter (L H shown)

  3

Burner assembly

  9

Flue outlet/combustion air inlet

  4

Ignition/detection electrode

 10

Fan to flue connection

  5

Gas connection

 11

Flue gas test point

  6

Multifunctional control

 12

Combustion air fan

1

This appliance has been tested and certified for use with natural gas.

1.

GENERAL DESCRIPTION

1

2

4

3

5

6

7

8

10

11

12

 9

Johnson and Starley prides itself on its ability to supply spare parts quickly and efficiently. If you have a problem in
obtaining a spare part, please contact Johnson and Starley Spares Department at the address below.

JOHNSON & STARLEY LTD.

Telephone:

(01604) 762881

Rhosili Road,

B r a c k m i l l s ,

 Telefax:

(01604)  767408

    Northampton NN4 7LZ

Содержание JANSTAR
















Отзывы: