Jobsite CT5305, Оригинальное руководство

Страница: 11 / 14

alignment at several points.
9. The edge of the set square and the saw blade should
be parallel.
10.
If the saw blade angles away from the set square,
adjust as follows.
11. Use an 10 mm wrench or adjustable wrench to
loosen the lock nut securing the 0 ° bevel adjustment
screw (29). Also, loosen the bevel lock (12).
12.
Adjust the 0 ° bevel adjustment screw (29) using a 4
mm hex key to bring the saw blade into alignment with
the square.
13.
Loosen the Phillips head screw holding the pointer of
the bevel scale (13) and adjust the position of the pointer
so that it accurately indicates zero on the scale.
Retighten the screw.
14. Retighten the bevel lock (12) and the lock nut
securing the 0 ° bevel adjustment screw (29).
SETTING THE FENCE SQUARE WITH THE TABLE
1. Make sure that the battery is removed from the power
point.
2. Push the saw arm (3) down to its lowest position and
engage the release knob (4) to hold the saw arm in the
transport position.
3. Loosen the mitre locks (20) and lifting up the mitre
latch (21).
4. Rotate the table (16) until the pointer is positioned at
0
°
.
5. Release mitre latch (21) and tighten the mitre locks
(20).
6.
Using a 5 mm hex key, loosen the two screws securing
the fence (14) to the base.
7. Place a square against the fence (14) and alongside the
blade.
8.
Adjust the fence (14) until it is square with the blade.
9. Tighten the screws securing the fence (14).
10. Loosen the Phillips head screw holding the pointer of
the mitre scale (17) and adjust it so that it accurately
indicates the zero position on the mitre scale.
11. Retighten the screw securing the mitre scale pointer.
CHANGING A BLADE
1. Make sure that the battery is removed from the power
point.
2.
Push down on the operating handle (5) and pull the
release knob (4) to disengage the saw arm (3).
3.
Raise the saw arm (3) to its highest position.
4. Loosen the cover plate screw about 2 turns with a
Phillips screwdriver. Do not remove this screw from the
tool.
5.
Pull the rotating blade guard (8) down. When the
rotating blade guard (8) is positioned over the upper
fixed blade guard (6) it is possible to access the blade
bolt.
6.
Lift and hold up the lower blade guard (8) to expose
the threaded blade bolt.
7. Hold the rotating guard (8) up and press the spindle
lock button (22). Rotate the blade until the spindle locks.
8.
Use the 6 mm hex key provided to loosen and remove
the blade bolt. (Loosen in a clockwise direction as the
blade screw has a left hand thread).
9. Remove the flat washer, outer blade washer and the
blade.
10.
Wipe a drop of oil onto the inner blade washer and
the outer blade washer where they contact the blade.
11. Fit the new blade onto the spindle taking care that
the inner blade washer sits behind the blade.
12.
Replace the outer blade washer.
13.
Depress the spindle lock button (22) and replace the
flat washer and blade bolt.
14. Use the 6 mm hex key to tighten the blade bolt
securely (tighten in an anti-clockwise direction).
15. Lower the blade guard, hold the rotating lower blade
guard (8) and blade bolt cover (10) in position and
tighten the fixing screw to secure the blade bolt cover in
position.
16. Check that the blade guard operates correctly and
covers the blade as the saw arm is lowered.
17. Connect the saw to the power supply and run the
blade to make certain that it is operating correctly.
CROSS CUT
If possible, always use a clamping device such as a ‘ G"
clamp to secure your workpiece.
When cutting your workpiece, keep your hands well
away from the blade area.
Do not remove a cut-off piece on the right-hand side of
the blade using your left hand.
A crosscut is made by cutting across the grain of the
workpiece. A 90
°
crosscut is made with the mitre table
set at 0
°
. Mitre crosscuts are made with the table set at
some angle other than zero.
1. Pull on the release knob (4) and lift the saw arm (3) to
its full height.
2. Loosen the mitre locks (20) and lifting up the mitre
latch(21) .
3. Rotate the mitre table (16) until the pointer aligns with
the desired angle.
4. Release mitre latch(21) and retighten the mitre locks
(20).