background image

9

CONTROLS AND OPERATION

CONTROLS

1/ Looking at the angle grinder from the top,
the spindle lock (2) is located at the front
top right hand side.
2/ There are attachment points (4) for the
handle (6) at either side of the front of the
housing, Attach the handle in the position
that suits the planned operation.
3/ An arrow imprinted on the front housing
indicates the direction of the rotation of the
Disc.
4/ The on/off switch (5) is located on the
top of the motor housing.
5/ The adjustable disc guard (3) is on the
underside of the grinder as is the outer
flange (9), grinding disc (10)

Operation

This angle grinder can be used for polishing
cutting and grinding.

1/ To start the grinder first ensure that the
work you are going to do has the right
disc for the job.

2/ When using cutting or grinding disc,
insure that the guard (3) and tools are
in good condition.

3/ Position the guard (3) when using disc
so that it will deflect hot sparks away from
operator.

4/ Plug the cord set into the mains outlet.

5/

Push the on/off switch (5) forward and

up over the latching ramp to lock the switch

on.

6/ Allow the grinder to start and attain full
speed before bringing the grinder to the work
piece.

7/ When using cutting and grinding discs
hold the grinder at 15

to 30

to the work

surface moving slowly

8/ Hold the grinder firmly while it is
switched on and only apply gentle pressure
to the work piece little more than the weight
of the tool should be applied to give the best
and most efficient material removal. Forcing
and excessive pressure can cause
dangerous disc fracture or damage to the
tool.

9/ Avoid flying sparks. And ensure they do
not hit any inflammable materials, as they
are very hot and could cause personal injury
or a fire.

10/ Once you have finished the job you are
doing

, press

the back of the switch (5) and

lift it over the latching ramp to stop the angle
grinder.

11/ If a person comes to you while you are
operating the machine do not turn round or
look up until you have released the trigger
and the machine has come to a stop and you
have put the machine down then you are
safe to communicate with that person.

12/

WARNING

. The grinder continues for a

few seconds after the trigger has been
released, so be careful when placing the tool
down, make sure it has stopped.

Содержание CT1649















Отзывы: