Joab EcoDrive VL10U страница 20 Скачать руководство пользователя | Manualshive

Страница: 20 / 57

background image

Skip Weight

This is used to measure the weight of a loaded skip when suspended from the rear of the
vehicle. The weight of the skip is constantly displayed in the radio controller as long as no other
function is being operated. To use this function follow the procedure below:

1.

Make sure that

Function_1

or

Function_2

mode is selected on the radio controller.

2.

Extend the lifting-arm out so that it is more
than 90 degrees to the bed of the skip-
loader, past vertical, as shown.

3.

Operate the folding-arm so that the
arrow-head on the folding-arm aligns with
the corresponding one on the lifting-arm.
When the arrows are aligned the weight
displayed in the radio controller is accur-
ate.

NOTE:

Although the weight of the skip is

constantly displayed in the radio controller, it is only accurate when the arrow on the fold-
ing-arm and lifting-arm are aligned, as described above.

Control Panel - Right Side

An additional control panel (see

Panel", on page 9

) can be fitted to the right

side of the skip loader. This gives the operator
the ability to operate the skip loader from both
sides of the vehicle and can be beneficial in
many aspects. However, only one side can be
active at a time. It is not possible to operate
both controllers simultaneously.

Extending-Body

Skip-loaders can be ordered with an extend-
ing-body. This allow for two skips to be trans-
ported on the same skip-loader.

Operation of the extending-body is done using
buttons 9 and 10, when in

Function_1

mode,

either on the control panel or the radio con-
troller.

For more information about the extending-
body and the handling of two skips, see

ling Double Skips", on page 35

14

Operation | Extra Options

EcoDrive VL10-VL18 manual: 1021046 Edition 2 | 2022-05-02

«
...
18
19
20
21
22
...
»

Содержание EcoDrive VL10U


























































Отзывы:

Нет отзывов

Похожие инструкции для EcoDrive VL10U

Бренд: Safeline Страницы: 8

Productivity 2000 P2-08NAS

Бренд: Automationdirect.com Страницы: 4

WELDER FANTASY BI-PULSE 201

Бренд: FACHOWIEC Страницы: 33

Бренд: HALDER Страницы: 2

Genie GS-2669 DC

Бренд: Terex Страницы: 147

Бренд: Nußbaum Hebetechnik Страницы: 32

Бренд: Gage Страницы: 36

Бренд: AXEM Technology Страницы: 31

Бренд: Feig Electronic Страницы: 35

Бренд: ATH Страницы: 76

Бренд: Magneti Marelli Страницы: 44

Бренд: Parweld Страницы: 16

Бренд: JLG Страницы: 48

MASTER LOAD 750

Бренд: Lincoln Electric Страницы: 28

Бренд: iWeld Страницы: 90

Бренд: Palfinger Страницы: 76

Бренд: R-Tech Страницы: 19

PROGYS CEL 250 TRI

Бренд: GYS Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды