background image

SECTION 3 - MACHINE CONTROLS, INDICATORS, AND OPERATION

31215090

3-11

Drive/Lift/Steer Joystick Control

Trigger (Enable) Switch

 - This trigger switch is located on the front

of the joystick controller. It acts as an enable and must be depressed
before operating the drive, steer, and lift functions. When released,
the function in operation will stop.

The speed on all functions is proportionally controlled by the dis-
tance from the neutral (center) position of the joystick controller.

NOTE:

Once the trigger switch is pressed, the operator has five seconds
to engage a function. After five seconds, the trigger switch must
be released and pressed again to operate.

NOTE:

If the machine is also equipped with a footswitch, depress the
footswitch in conjunction with the trigger (enable) switch
located on the joystick controller. Power is removed from the
platform controls when the footswitch is released.

Steer Switch

 - The steer switch is a thumb-operated switch located

at the top of the joystick controller handle. Depressing the switch to
the right will steer the wheels to the right. Depressing the switch to
the left will steer the wheels to the left.

Joystick Controller

 - This controls drive and lift.

Steering and Traveling

DO NOT DRIVE WITH THE PLATFORM ELEVATED EXCEPT ON A SMOOTH, FIRM SURFACE
WITHIN THE LIMITS OF THE MAXIMUM OPERATING SLOPE THAT IS FREE OF OBSTRUC-
TIONS AND HOLES.

TO AVOID LOSS OF TRAVEL CONTROL OR UPSET ON GRADES AND SIDESLOPES, DO NOT
DRIVE MACHINE ON GRADES OR SIDESLOPES EXCEEDING THOSE SPECIFIED IN SEC-
TION 6.2, MACHINE DIMENSIONS, OR
 SHOWN IN SECTION 3.9, GRADE AND SIDE-
SLOPE.

BEFORE DRIVING, LOCATE THE DECALS WITH THE BLACK/WHITE ORIENTATION
ARROWS ON THE CHASSIS AND THE PLATFORM CONTROLS. MOVE THE JOYSTICK IN
THE DIRECTION OF THE BLACK OR WHITE ARROW THAT MATCHES THE COLOR OF THE
ARROW ON THE CHASSIS FOR THE INTENDED DIRECTION OF TRAVEL.

IF THE TILT INDICATOR WARNING LIGHT/ALARM IS ACTIVATED WHILE DRIVING WITH
PLATFORM RAISED, LOWER PLATFORM COMPLETELY AND DRIVE TO A SMOOTH, FIRM
SURFACE WITHIN THE LIMITS OF THE MAXIMUM OPERATING SLOPE.

1.

Place key selector switch at the ground control station to 
platform operation.

2.

Position emergency stop switches, one at the platform and 
one at the ground control station to the ON position.

To 

order go 

to

Discount-Equipment.com

Содержание R2632
































































































Отзывы: