JLA D90 Скачать руководство пользователя страница 34

Страница: 34 / 40

JLA Limited

113374 - 4

NOTE:

To prevent damage, avoid cleaning and/or touching the Direct Spark Ignitor.

Remove lint accumulation from inside.

6 MONTHS

Inspect and remove lint accumulation in customer furnished exhaust ductwork system and from dryer’s internal exhaust
ducting.

NOTE: THE ACCUMULATION OF LINT IN THE EXHAUST DUCTWORK CAN CREATE A

POTENTIAL FIRE HAZARD

NOTE: DO NOT

OBSTRUCT THE FLOW OF COMBUSTION AND VENTILATION AIR. CHECK

CUSTOMER FURNISHED BACK DRAFT DAMPERS IN THE EXHAUST DUCTWORK.
INSPECT AND REMOVE ANY LINT ACCUMULATION, WHICH CAN CAUSE THE
DAMPER TO BIND OR STICK.

NOTE:

A back draft damper that is sticking partially closed can result in slow drying and shut down of the heat
circuit safety switches or thermostats.

NOTE:

When cleaning the dryer cabinet(s), avoid using harsh abrasives. A product intended for the cleaning
of appliances is recommended.

Check

ALL

V-belts for tightness and wear. Retighten, realign, or replace if required.

NOTE:

V-belts

should be

replaced in matched sets (pairs).

B. ADJUSTMENTS

7 DAYS AFTER INSTALLATION and EVERY 6 MONTHS THEREAFTER

Inspect bolts, nuts, screws, setscrews, grounding connections, and nonpermanent gas connections ( unions, shutoff valves,
and orifices). Fan (impellor) V-belts, along with the motor and drive belts

should be

examined and replaced if necessary.

Tighten loose V-belts when necessary. Complete operational check of controls and valves. Complete operational check
of

ALL

safety devices (door switches, lint drawer switch, sail switch, burner, and hi-limit thermostats).

NOTE:

Squirrel cage type fan (impellor) on the blower motor

must be

inspected and cleaned every 6 months.

C. LUBRICATION

The fan shaft bearings and

ALL

the basket (tumbler) drive shaft and idler shaft bearings

must be

lubricated every 3

months. Use a #2 grease or its equivalent. Lubrication is necessary or premature bearing failure will be the result.

The motor bearings are permanently lubricated and

DO NOT

require to be serviced.

Содержание D90









































Результаты поиска

Содержание D90

Отзывы:

Похожие инструкции для D90

Бренды по названию

Популярные бренды

JLA D90, Руководство по установке

Результаты поиска

Содержание D90

Отзывы:

Похожие инструкции для D90

Бренды по названию

Популярные бренды