background image

Stealthbox

®

I N S T A L L A T I O N   G U I D E

S B - F - RT R K C T R / 1 2 W 3 v 2 - D 2 ,   J L   AU D I O,   I n c   2 0 0 2

S h e e t   S K U # 0 1 1 1 5 9     R ev i s i o n   1 1 / 1 8 / 2 0 0 3

Pa g e  1

for the

SB-F-RTRKCTR/12W3v2

Rear Console Only

(Fits 2002-Up Ford SuperCrew

Harley Davidson, King Ranch;

2001-2002 Lincoln Navigator and 

2002 Blackwood )

This Stealthbox is a product

which requires professional
installation skills and tools.
Please read this installation guide
thoroughly before beginning the
project. It will guide you step by
step through the installation. Several
of the steps in this process may
require two people to accomplish.

It is absolutely vital that the

enclosure be properly mounted to
the vehicle according to these
instructions. Failure to mount the
enclosure properly presents two
problems: 1) The  sub-bass
performance will suffer due to the
movement of the enclosure caused
by the force exerted by the
woofer(s) and 2) A loose enclosure
presents a serious safety hazard in
the event of a collision or sudden
deceleration.

Please enjoy your JL Audio

Stealthbox responsibly.

STEP 1:

Remove front exposed pocket,

internal instert and rubber flooring.

STEP 2:

With an 8mm socket and long

extenstion, remove the four bolts. Located
where the front pocket was removed from in

STEP 1

.

STEP 3:

Remove the pair of bolts from side

rear of the OEM console.

You will have to lower the two rear seats and
lift up drop flooring to expose the bolts.

After the pair of bolts are removed, remove
OEM console out of truck.

STEP 4:

With the OEM console removed

you , unbolt the rear bracket.

STEP 5:

The Stealthbox is shipped with two

brackets attacahed to it. Remove the rear
angle bracket from the Stealthbox.

Mount this black angle bracket to where the
OEM bracket was removed.

Use the three bolts that was removed in

STEP4

.

STEP 6:

The top picture shows how the front

bracket is installed when shipped.

Remove all mounting hardware and flip the
front bracket. Remount the flipped bracket
with the same hardware.

The bottom picture shows the bracket
properly mounted for install.

START 

HERE

Continued on Page 2

w w w . j l a u d i o . c o m

Содержание Stealthbox SB-F-RTRKCTR/12W3v2

Страница 1: ...in the event of a collision or sudden deceleration Please enjoy your JL Audio Stealthbox responsibly STEP 1 Remove front exposed pocket internal instert and rubber flooring STEP 2 With an 8mm socket and long extenstion remove the four bolts Located where the front pocket was removed from in STEP 1 STEP 3 Remove the pair of bolts from side rear of the OEM console You will have to lower the two rear...

Страница 2: ... bolts 6 are shown in the picture 7th is under strap not seen STEP 14 With Steathbox mounted place the OEM console shell over Stealthbox Push in the supplied pair of tree locks to each side of the OEM console STEP 15 Using a 1 8 drill bit drill into upper sides of the Stealthbox Using the OEM screw holes as guides Use the four screws that was removed in STEP12 to mount outside shell to the Stealth...

Страница 3: ...guides STEP 19 Using the six out of seven T 15Torx bolts that was removed in STEP 10 mount lid STEP 20 With lid mounted drill 7th hole using a 1 8 drill bit Don t forget to bolt down lid strap with the 7th t 15Torx screw SB F RTEKCTR 12W3v2 D2 JL AUDIO Inc 2002 Sheet SKU 011159 Revision 11 18 2003 Page 3 w w w j l a u d i o c o m STEP 16 Use masking tape to mark cutting template IMPORTANT Please r...

Страница 4: ... installing and tuning this amplifier STEP 21 Mount lid strap using the 7th T 15Torx bolt STEP 22 With OEM outer console OEM inner cut console and hinged lid mounted Look in the lid latch catch located on the front of OEM inner console You will see the small angle bracket that was mounted in STEP 11 Drill 1 8 hole through the lid latch catch using the hole from the small angle bracket as a guide M...

Отзывы: