JinkoSolar JKM M-72HL4-BDVP Series Скачать руководство пользователя страница 5

Страница: 5 / 34

-3-



During all transportation situations, never drop the module from a vehicle, house or hands.

This will damage module.



Modules (glass, junction boxes, connectors, etc.) shall be protected from long-term exposure

to environments containing sulfur, strong acid, strong alkaline, etc., which may pose a risk

of corrosion to the product.



Do not clean the glass with chemicals. Only use tap water. Make sure the module surface

temperature is cool to the touch. Cleaning modules with cool water when module surface

temp is high may result in glass breakage. Do not brush paint or corrosive substances on

the surface of the modules.



Do not disconnect any of the modules when under load.



When looking at PV modules with anti-reflection (AR) coating technology, it will be normal

to see some cells with a slight color difference at different angles. Modules with LRF(light

reflective film) and without LRF should not be built in the same array or roof.



The junction box connector should not be in contact with oily substances, organic solvents

and other corrosive materials to avoid damage to the connector. For example, alcohol,

gasoline, lubricants, rust inhibitors, herbicides and so on.



Before the installation of modules, it is recommended to add rainproof facilities in the project

site to avoid direct open-air placement.



Corner protection of DV module is used to protect the module during transportation, and the

customer can remove or leave it on modules.



Connector of junction box can not be contacted with oily substances, for example, lubricant,

rust inhibitor etc.



The maximum altitude the PV module is designed for ≤ 2000m.



Meaning of crossed

–out wheeled dustbin:

Do not dispose of electrical appliances as unsorted municipal

waste, use separate collection facilities.

Contact your local government for information regarding the

collection systems available.

If electrical appliances are disposed of in landfills or dumps,

hazardous substances can leak into the groundwater and get into

the food chain, damaging your health and well-being.

When replacing old appliances with new ones, the retailer is

legally obligated to take back your old appliance for disposals at

least free of charge.

Содержание JKM M-72HL4-BDVP Series



































Результаты поиска

Содержание JKM M-72HL4-BDVP Series

Отзывы:

Похожие инструкции для JKM M-72HL4-BDVP Series

Бренды по названию

Популярные бренды

JinkoSolar JKM M-72HL4-BDVP Series, Руководство по установке

Результаты поиска

Содержание JKM M-72HL4-BDVP Series

Отзывы:

Похожие инструкции для JKM M-72HL4-BDVP Series

Бренды по названию

Популярные бренды