background image

TPY

R

TPY

R

7

8

Depending on specific activities,extra safety measures may be 
requires.Contact TPY if a potential danger arises during use.

ATTENTION

Make sure that the product operates within its working range.
Only then the product performance is guaranteed

ATTENTION

Not only must the general safety instructions laid down in
this chapter on "Safety" be complied with,but also the safety
instruction outlined under specific headings

4.2

  Users

All personnel in volves in the operation, maintenance,inspection

 and installation of the product must be fully qualified to carry out

the work involved.
Personal responsibilities,competence and supervision must be

clearly defines by the operator.if the personnel in question is not

already in possession of the requires know-how,appropriate

training and instruction must be provided.if required,the operator

may commission the manufacturer/supplier to take care of such

training.In addition,the operator is responsible for ensuring that

the contents of the operating instructions are fully understood by

the responsible personnel.

4.3

  Safety provisions

The product has been designed with the greatest possible care.
Original parts and accessories meet the safety regulations.
Modifications in the construction or the use of non-original parts
may lead to a safety risk.

ATTENTION

Make sure that the product operates within its working 
range.only then the product performance is guaranteed

4.3.1

  Lable on the product

The icons,warnings and instructions applied to the product are
part of the safety provisions.The lables may not be removed or
covered.Lables must remain legible during the entire life of the
product.Replace damaged lables immediately.

     power supply.

 

     Cover the parts that can become hot,so direct contact is impossiple.

 

     When applicable,always place undeformed coupling protection
     plates to protect the coupling,before putting the pump into use.

     Make sure that the coupling protection plates are never in contact

      with the running coupling.

 .

     Always close the terminal box on the pump.

4.4

  Safety precautions

 

     Contact the local electricity company for questions   about the

4.4.1

  During normal use 

Содержание DL(JGGC) 12






















Отзывы: