background image

TPY

R

TPY

R

5

6

3

Warranty

3.1

  

Terms of warranty

The warranty period is settled by the terms of your contract or at
least by the general terms and conditions of sales.

ATTENTION

Modification or alterations of the product supplied are only
permitted after consultation with the manufacturer.Original
spare parts and accessories authorized by the manufacturer
ensure safety.The use of other parts can invalidate any liability
of the manufacturer for consequential damage

ATTENTION

The warranty relating to the opeating reliability and safety
of the product supplied is only valid if the product is used in
accordance with its designated use as described in the
following sections of this manual.The limits   stated in the
data sheet must not be exceeded under any circumstances

The warranty becomes invalid if one or more of the points below occur

    The buyer makes modifications himself

1/3

    The buyer carries out pepairs himself or has these carried out by a third party.

    The product has been handled or maintained improperly.

    The product has non original TPY spare parts fitted

     

remedies  defects  under  warranty

TPY 
if the points blow are observed

    Defects are caused by flaws in the design,the material or the production.

    The defect has been reported within the warranty period

Other terms of warranty have been included in the general terms
of delivery,which are available upon request.

4

Safety and environmnt 

4.1

General

This TPY product has been developed using state-of-the-art technology;it is 
manufactured with utmost care and subject to continuous quality control.TPY 
does not accept any liability for damage and injure caused by not observing 
the directions and instructions in this manual.This also applies in cases of 
carelessness during the installation procedure, use and maintenance of the 
product.Non-compliance with safety instructions can jeopardize the safety of 
personnel,the environment and the product itsself.Non-compliance with these 
safety instructions will also lead to forfeiture of any and all rights to claims for 
damages. 
For exanple,in particular non-compliance can result in:

  failure of important pump/system functions

  failure of prescribed maintenance and servicing practices

  injure to persons by electrical,mechanical and

    chemical effects

  hazard of the environment due to leakage

    of hazardous substances

 explosions

Содержание DL(JGGC) 12






















Отзывы: