Jiaxing Harley Baby Car HL228, Инструкция по эксплуатации

Страница: 19 / 23

1.Place the rear bumper support frame at the bottom side of the main body. Fix it with 10 screws . DO NOT OVERTIGHTEN,
in order to avoid damage of the screw or the parts . See FIGURE 1.
2.Mount the left side support and the left pedal and tighten it with 4 screws, as shown in the figure. Repeat the same
procedure at the right side. See
FIGURE 2.
3.Place the assembled side support and side pedal at the bottom side of the body at the place intended for them, as shown
in the figure. Tighten with 8 screws
. DO NOT OVERTIGHTEN, in order to avoid damage of the screw or the parts. See
FIGURE 3.
4.Mount the rear wheels as per figure 4. Insert a pin in the opening of the rear axle and bend it in a M–shape with pliers.
Attach the hubcap at the middle. Repeat the same procedure at the other side. See
FIGURE 4.
5.Mount the front wheels as per figure 5. Insert a pin in the opening of the front axle and bend it in an M–shape with pliers.
Attach the hubcap at the middle. Repeat the same procedure at the other side. See
FIGURE 5.
6.Mount the partition (horizontal) in the openings in the main body at the places intended for that purpose, as shown in the
figure. See
FIGURE 6.
7.Mount the partition (vertical) in the openings in the main body at the places intended for that purpose, as shown in the
figure. See
FIGURE 7.
8.Connect the plug of the cables of the steering wheel to the cables coming out of the front jeep body. Place the steering
wheel on the steering shaft and tighten it with a screw and nut. See
FIGURE 8.
9.Mount the windshield at the opening in the main body fasten it with two screws. See FIGURE 9 and FIGURE 10.
10.Mount the spoiler at the opening in the main body and fasten it with four screws. See FIGURE 11.
11.Mount the side window at the opening in the door and fasten it with four screws. Repeat on the other side. See FIGURE
12.
12.Mount the side mirror at the opening in the door Repeat at the other side. See FIGURE 13.
13.Mount the seat at the opening in the main body at the place intended for that purpose and fasten it with two screws.
Repeat at the other side . See
FIGURE 14.
14.Mount the backrest at the opening in the main body and fasten it with one screw. Repeat at the other side. See FIGURE
15.
18
USE OF THE BATTERY OPERATED JEEP
Notice:
A. When you change the direction of movement, first make sure that the jeep does not move. Otherwise, if you change
suddenly the direction of movement without stopping the jeep, you may cause damage of the gears and motor.
B. If you are using the remote control, please, follow the guidelines inn this instruction manual.
 On Figure U are shown the following buttons:
1 – Fast/ Low speed; 2 – ON/ OFF Button; 3 – Lights Button; 4 – Pedal; 5 – Forward/ Backward switch; 6 – Multifunctional
dashboard with FM, English tales, MP3 input, TF-card, USB, Volume control button, Battery Indicator.
1.Start: Switch the power button to open position and the jeep must be in active mode.
2.Forward: Press the Forward-Backward switch to Forward position. Press the pedal and the jeep will start moving
forwards.
3. Backward: Press the “forward-backward” switch to „backward”. position. Press the pedal and the jeep will start moving
backwards.
4.Speed change:
- Low Speed: The jeep is pre-set to be operated at low maximum speed of 4 km/h (2.5m/h).
- High Speed: After your child has good skills to use the jeep and to understands the rules of safe driving, then the child
can use the jeep at high speed. The highest speed that the jeep can reach is 5 km/ h.
5.Stop: The jeep will automatically stop after you release the gas pedal.
6.Music effects: Press any of the buttons on each side of the steering wheel. Each buttons corresponds to different musical
effects.
7.MP3: Turn the power button on and connect one end of the MP3 cable to the output of the dashboard, connect the other
to the MP3 player.
Do not put the MP3 player close to the ears and do not listen to loud music, because this may lead to
impairment of the hearing.
REMOTE CONTROL USE
WARNING! The remote control can be used by an adult only!
I. PLACING OF THE BATTERIES: The batteries are not included in the set. Remove the screw of the lid of the battery
compartment with a screwdriver and set it aside. Place the batteries by observing the correct polarity marked on the bottom
of the compartment. Use the correct size batteries. Replace the cover of the battery compartment and secure it with the
screw.
 The remote control can be activated by 2 pcs AAA 1.5V batteries.
Warning! The further change of the batteries must be done by an adult.