Jetter JM-105 Скачать руководство пользователя страница 74

Страница: 74 / 106

7 Description of Connections

Jetter AG

7.8

Sin- / Cos-Encoder Connection

7.8.1

Specification

Specification of the Connector for Terminal X61 (ENCODER)

• 15-pin high density SUB-D connector (male)
• Metallized enclosure

Sin-Cos Encoder Cable Specifications

• Cable cross-sectional area of at least 3 * 2 * 0.14 mm² + 2 * 0.25 mm² min.
• 2 * 0.25 mm² must be used for the power supply unit and for GND
• Twisted-pair cables shielded with the all-over shield must be used; the signal lines

must also be twisted in pairs:
Sine + and reference sine
and reference cosine
Index + and reference index
0 V and voltage supply

• The shield must be connected to the connector housings on both ends of the

cable with the greatest possible surface area.

• Material: Copper
• Temperature class: 60 °C
• Maximum cable length: 50 m

Содержание JM-105











































































































Результаты поиска

Содержание JM-105

Отзывы:

Бренды по названию

Популярные бренды

Jetter JM-105, Руководство пользователя

Результаты поиска

Содержание JM-105

Отзывы:

Бренды по названию

Популярные бренды