manualshive.com logo in svg

JETStream 4 J-FORCE GEN III JF4X15, Инструкция по эксплуатации продукта, Страница: 8 / 38

Поделиться
Скачать
JETStream 4 J-FORCE GEN III JF4X15 Скачать руководство пользователя страница 8

8

PI-197

January 2022

only be properly installed with hydraulic crimping equipment.

NOZZLES

1.  Read General Safety 

section. 

2. 

Nozzle flow ratings must be compatible with pump discharge and 

pump pressure rating. (See Nozzle Flow Rating Chart on page 25.)
3.  Use only nozzles with a manufacturer’s pressure rating of at least 

the operating pressure or a burst rating or no less than 3.0 times the 

desired operating pressure.
4. 

Prior to installation, make sure the nozzle has no clogged orifices.

5. 

Apply 3 - 4 wraps of Teflon tape to male connection threads on the 

nozzle. Apply anti-seize compound over the sealant tape for additional 

protection against galling in connection threads. Wrench connection 1 

1/2 - 2 turns past hand tight. A minimal thread engagement of four (4) 

threads should exist on all Jetstream NPT pipe connections.
6. 

Use wrench flats (when available) or a properly 

adjusted smooth jaw plier wrench (JS PN 64119) to tighten nozzle. Avoid 

using pipe wrench as wrench marks will cause nozzles to crack and fail.
7. 

Blocked orifice(s) can cause excessive system pressure and failure. 

If orifice(s) appear clogged or partially blocked with dirt or debris, 

remove nozzle from J-Force and clean immediately.

8. 

Remove nozzle from service if:

A.  Nozzle is split or damaged;
B.  Nozzle sidewall is worn by more than 25% at any point;
C.  Nozzle’s ability to hold pressure is questionable
D.  Threads are missing or damaged

FLEXIBLE TUBE CLEANING LANCES

1.  Read General Safety 

section and Nozzle Safety Warnings prior to  

connecting flex lances.

2.  Do not

 use a flex lance with a burst rating less than 2.25 times 

the pressure at which it will operate. 10,000 psi operating pressure 

flex lances 

must

 have a 

minimum

 22,000 psi burst rating. 8,000 psi 

operating pressure flex lances 

must

 have a 

minimum

 18,000 psi burst 

rating.

Содержание 4 J-FORCE GEN III JF4X15







































Отзывы:

Нет отзывов