JETStream 4 J-FORCE GEN III JF4X15 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 38

JETStream 4 J-FORCE GEN III JF4X15 Скачать руководство пользователя страница 12

12

PI-197

January 2022

SECTION 2: PRODUCT DESCRIPTION

The 4” J-Force

TM

Gen III is a self-powered rotating nozzle that uses up to

8 JS2 or P2TCS nozzles.
The 4” J-Force Gen III has many features, including:
•

Spins on a film of high pressure water and has no ball bearings to

replace. No oil or grease is needed for lubrication.

• Comes equipped with an eddy-current braking system which

controls rotation speed for maximum cleaning power and minimum

wear.

•

Completely field repairable (in less than 5 minutes)

• 10° forward, 45° forward, 100° radial, 135° rearward nozzle angles
• Designed to easily navigate and clean 4” pipes with 90° bends.

This system contains several high-energy, rare-earth

magnets that produce a magnetic field. Persons with a pacemaker

or other electronic medical device must use extreme caution when

handling or in close proximity. It is recommended that a minimum

distance of 6 inches (152mm) be maintained at all times between the

J-Force and any electronic medical devices.

The use of gloves is recommended when handling the

tool after operation as the body may reach temperatures greater than

200°F.

«
...
10
11
12
13
14
...
»

Содержание 4 J-FORCE GEN III JF4X15







































Отзывы:

Нет отзывов