manualshive.com logo in svg

JETStream 3000 series, Руководство по эксплуатации, Страница: 11 / 84

Поделиться
Скачать
JETStream 3000 series Скачать руководство пользователя страница 11

Bareshaft Pump

3

Purge the System

Before attaching a nozzle to the control gun or tube 

cleaning lance, operate the pump at low speed to 

purge dirt and debris from the system. Dirt and 

debris can clog nozzle orifice(s) and cause exces

-

sive system pressures.

Test the System

With the nozzle installed, operate the pump at low 

speed (low pressure) to test the system. Should 

system repairs or adjustments be necessary, stop 

the pump and relieve all pressure before performing 

any required repairs or adjustments.

Slowly Increase Pressure

Visually inspect all fittings for leaks at 1000 psi (69 

bar), and then again once the system reaches full 

pressure. Do not use your hand to find leaks. If leaks 

are evident, turn the system off and relieve the pres-

sure. Remove the leaking fitting, clean and inspect. 

If the fitting looks undamaged, re-install the fitting. 

If the leak persists, the fitting must be replaced. 

Leaking fittings can cause fitting damage and very 

dangerous injection wounds.
With the system operating properly, slowly increase 

pump speed until operating pressure is reached.

Use the Minimum Pressure Required

Do not exceed the operating pressure of the sys-

tem’s lowest pressure-rated component. Use of low-

er pressure-rated components in a system should 

be avoided if possible. Components with a lower 

pressure rating can be overlooked and explode if 

vigilance is not maintained. Keep equipment pres-

sure rating and warning tags intact.

Be Prepared

If equipment malfunctions or a malfunction is suspect-

ed, immediately stop the cleaning activity and relieve 

the pressure in the system before attempting any re-

pair. Always follow manufacturer’s repair instructions.

Performing Maintenance or Repairs

Because of the hazards involved with water blasting, 

maintenance or repairs may only be performed by 

service personnel that are properly trained to main-

tain this equipment. Training is available through 

Jetstream

®

 and can be requested from the Jetstream 

website (

www.waterblast.com

) or FS Solutions rental 

centers.
Following repairs or maintenance, operate the sys-

tem at low pressure to test the system. Adjust the 

pressure slowly during operation.

Freezing Conditions

After shutting down in freezing conditions, even for 

brief periods, drain the water from all components. 

Prior to starting the equipment after a freeze, the 

operation of all equipment components must be 

checked carefully to ensure they are not frozen, or 

cracked, and are still in safe operating condition. 

Refer to”Winterizing the Pump” on page 19” for 

details.

Store Components Properly

Properly store components to protect from damage 

when not in use. Ensure all warning tags and mark-

ers remain intact for the next usage.

Содержание 3000 series





















































































Отзывы:

Нет отзывов