background image

 

30.  Don’t use in dangerous environment. Don’t use 

power tools in damp or wet location, or expose 
them to rain. Keep work area well lighted. 

 

Additional  safety  instructions  for 
scroll saws 

31.  Scroll  saw  must  be  secured  to  a  sturdy 

foundation. If there is a tendency for the stand 
or workbench to move, it must also be secured 
to the floor. 

32.  Blade  must  be  properly  tensioned  before 

operating. Failure to do so could result in blade 
breakage and possible injury. 

33.  Never  start  saw  with  workpiece  contacting 

blade. 

34.  Always  keep  fingers  and  hands  away  from 

blade. Avoid awkward hand positions where a 
sudden slip might cause hand to move into or 
toward the blade. 

35.  Always  hold  stock  firmly  against  table.  The 

provided  hold-down  should  be  correctly 
positioned over the workpiece.  

36.  Do not attempt to saw any stock that does not 

have a flat surface, without a suitable support. 
Do not cut pieces of material too small to hold 
by hand.  

37.  Care must be taken when cutting material with 

an  irregular  cross  section.  The  blade  could 
pinch  before  the  cut  is  completed.  Any  stock, 
such as frame molding, must lie flat on the table 
surface and not be allowed to rock. 

38.  Dowels or tubing have a tendency to roll while 

being cut and cause the blade to “bite.” Round 
material should be held firmly against the table. 

39.  Turn  off  saw  before  backing  stock  out  of  an 

incomplete  cut.  Only  remove  jammed  cut-off 
pieces after blade has stopped. 

40.  Make “relief” cuts before cutting long curves. 

41.  When  cutting  large  or  oversize  stock,  always 

make sure material is supported at table height. 

42.  Do  not  feed  workpiece  too  fast  while  cutting. 

Feed workpiece only fast enough for the blade 
to cut. 

43.  Never  reach  under  the  table  while  blade  is 

moving. 

 

 

 

 

Familiarize yourself with the following safety notices used in this manual: 

 This means that if precautions are not heeded, it may result in minor injury and/or possible 

machine damage. 

 This means that if precautions are not heeded, it may result in serious, or possibly even fatal, 

injury.

SAVE THESE INSTRUCTIONS 

 

 

WARNING:

 This product can expose you to 

chemicals  including  lead  and  cadmium  which 
are  known  to  the  State  of  California  to  cause 
cancer  and  birth  defects  or  other  reproductive 
harm,  and  phthalates  which  are  known  to  the 
State of California to cause birth defects or other 
reproductive  harm.  For  more  information  go  to 
http://www.p65warnings.ca.gov. 

 

WARNING:

  Drilling,  sawing,  sanding  or 

machining wood products generates wood dust 
and  other  substances  known  to  the  State  of 
California to  cause cancer.  Avoid  inhaling dust 
generated  from  wood  products  or  use  a  dust 
mask  or  other  safeguards  for  personal 
protection. 

Wood  products  emit  chemicals  known  to  the 
State of California to cause birth defects or other 
reproductive  harm.  For  more  information  go  to 
http://www.p65warnings.ca.gov/wood. 

Содержание JWSS-18B

































Отзывы: