Jet JWSS-18B Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 32

Jet JWSS-18B Скачать руководство пользователя страница 19

19

12.5

Tooth form

Figure 12-2 shows common blade forms. Tooth
form has an effect on cutting rate.

Regular:

Standard blade form with evenly spaced

teeth and zero-degree rake angle. Offers clean cuts
at slower feed rates.

Skip Tooth:

More space between teeth, for good

chip removal and fast cuts.

Double Tooth:

A skip tooth with larger gaps

between tooth sets; good chip removal, fast cutting.

Reverse Tooth:

Prevents underside tear-out,

leaves clean edge.

Spiral:

Cuts on all sides without turning workpiece;

limited application but good for looser fretwork.

Crown Tooth:

Cuts on both up and down strokes

for clean, splinter-free edges. Depending on blade
oscillation settings, a crown tooth blade may often
be turned over for a fresh set of cutting teeth.

Figure 12-2: blade forms

13.0

Optional accessories

These accessory items, purchased separately, will provide convenience and enhance the functionality of your
scroll saw. Contact your dealer to order, or call JET at the phone number on the cover.

727300S

Steel stand

727201

Lower Blade Holder (set of 3)

JWSS22B-253

Foot Switch Assembly

JWSS22B-335

Blade Storage Rack

(Can be mounted to wall,

workbench, or other surface

near the scroll saw; screws not

included)

98-0130

Casters (set of 4)

«
...
17
18
19
20
21
...
»

Содержание JWSS-18B

































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды