Jet JWS-35X Series Скачать руководство пользователя страница 16

Страница: 16 / 49

The arbor must be locked as described in

Spindle

Attachment Installation,

step 2.

1. Remove the draw bar (O).

2. Loosen the

spindle nut

(D) then, using the

spindle wrench

(Inset A) continue to turn until

the spindle breaks free of the arbor.

Shaper Cutter Installation

Note:

Spindle installation is described in the

previous section.

When changing tools, making

adjustments, or doing clean-up and maint-
enance, always turn the machine off and
unplug the machine from its power source.

Locking the Spindle

1. Locate

the

spindle lock

(L, Fig. 14) accessible

through the door on the right side of the
cabinet. Pull out and rotate 90º right

left,

resetting the knob into the indent.

Attempt to turn the

spindle assembly

(B, Fig. 14) by hand to verify that it is locked
and will not rotate.

Installing the Shaper Cutter

Referring to Figure 15:

2. Using an 8mm hex wrench (provided),

remove the

socket head cap screw

(F).

3. Remove

the

washer

(E),

keyed collar

all or as many

collars

(B) as necessary.

4. Place the

shaper

cutter

(A)

(not included)

onto the spindle, oriented in the proper
direction.

5. Place the

collars

(B) and

keyed collar

(C)

onto the spindle.

Note:

Collars

come in several widths and the

stacked selection (B) must be such that the
top of the

keyed collar

the top of the

spindle

(D). This will ensure

sufficient pressure to properly secure the

shaper cutter (

A) when installation is

complete.

6. Replace

the

washer

(E) and

socket head cap

screw

(F). Tighten screw with the

8mm

hex

wrench provided.

Unlocking the Spindle

7. Pull

out

the

spindle lock

(L, Fig. 14)

accessible through the door on the right side
of the cabinet. Rotate 90º right

left,

resetting the knob into the indent.

Using gloves to prevent injury from the

Figure 15

Содержание JWS-35X Series


















































Результаты поиска

Содержание JWS-35X Series

Отзывы:

Похожие инструкции для JWS-35X Series

Бренды по названию

Популярные бренды

Jet JWS-35X Series, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание JWS-35X Series

Отзывы:

Похожие инструкции для JWS-35X Series

Бренды по названию

Популярные бренды