background image

 21

Index No  Part No 

Description 

Size 

Qty 

50 .............. JBG6A-50 .................. Eye Shield Plate - left. .............................................  ...................................... 1 
 .................. JBG8A-50 .................. Eye Shield Plate - left. .............................................  ...................................... 1 
52 .............. TS-0720071 .............. Lock Washer ............................................................ 1/4" ................................ 1 
53 .............. TS-0680021 .............. Flat Washer ............................................................. 1/4" ................................ 3 
54 .............. JBG6A-54 .................. Cross Screw ............................................................ 1/4" x 1/2"...................... 1 
 .................. JBG8A-54 .................. Cross Screw ............................................................ 1/4" x 1/2"...................... 1 
54A ............ JBG6A-54 .................. Cross Screw ............................................................ 1/4" x 3/8"...................... 2 
55 .............. JBG6A-55 .................. Eye Shield Plate - left ..............................................  ...................................... 1 
 .................. JBG8A-55 .................. Eye Shield Plate - left ..............................................  ...................................... 1 
 .................. JBG10A-55 ................ Eye Shield Plate - left ..............................................  ...................................... 1 
57 .............. JBG6A-57 .................. Lock Hub (JBG-6A/8A) ............................................ 1/4" ................................ 1 
58 .............. JBG6A-58 .................. Cross Screw ............................................................ 3/16" x 3/8".................... 2 
59 .............. JBG6A-59 .................. Eye Shield ...............................................................  ...................................... 1 
  .................. JBG6A-59A ...............  Eye  Shield  Assembly ...............................................  ...................................... 1 
 .................. JBG8A-59 .................. Eye Shield  ..............................................................  ...................................... 1 
  .................. JBG8A-59A ...............  Eye  Shield  Assembly ...............................................  ...................................... 1 
60 .............. JBG6A-60 .................. Eye Shield Bracket Plate .........................................  ...................................... 1 
61 .............. JET-92 ....................... JET Logo ................................................................. 92x38mm ...................... 1 
63 .............. JBG6A-63 .................. Direction Label .........................................................  ...................................... 1 
64 .............. JBG6A-64 .................. Rubber Foot (6A/8A)................................................  ...................................... 4 
65 .............. JBG6A-65 .................. Switch Seat ..............................................................  ...................................... 1 
 .................. JBG8A-65 .................. Switch Seat ..............................................................  ...................................... 1 
66 .............. JBG6A-66 .................. Centrifugal Start Switch ...........................................  ...................................... 1 
 .................. JBG8A-66 .................. Centrifugal Start Switch ...........................................  ...................................... 1 
67 .............. LM000297 ................. ID Label, JBGM-6 ....................................................  ...................................... 1 
 .................. LM000298 ................. ID Label, JBGM-8 ....................................................  ...................................... 1 
68 .............. LM000299 ................. Warning  Label, JBGM.............................................. 2-3/4"  x  4-1/4" ............... 1 
 
 
 
MultiTool Attachment: 
 
 .................. 577115 ...................... Contact Wheel (not shown) ..................................... 2” x 3-1/2” ..................... 1 
 
For other replacement parts on the Mulitool attachment, contact Multitool at 800-660-0880. 
 
 
 
 

 
 

 
 

 
 

 

 

 

 
 
 
 
 
 
 

 

 

Содержание JBGM-6

























Отзывы: