Jet HBS-1220DC, Инструкция по эксплуатации и каталог запасных частей

Страница: 7 / 32

7
Read and understand the entire
contents of this manual before attempting
assembly or operation. Failure to comply may
cause serious injury.
5.0 Setup and assembly
5.1 Shipping contents
1 Band saw with installed blade
1 Work
stop assembly
1 Operating Instructions and Parts Manual
1 Product
registration card
1 Factory-cut test piece
1 Tool box (# HBS1220DC-TBC), containing:
4 Leveling
pads
4 Hex cap screws M16x74 (for leveling)
4 Hex nuts M16 (for leveling)
1 Phillips screwdriver
1 Flat blade screwdriver
1 Set of hex wrenches, 2.5~10mm
1 Open end wrench, 22/24mm
5.2 Uncrating and spotting
1. Finish uncrating the saw and inspect for
damage. Should any have occurred, contact
your local distributor. Do not discard packing
material until saw is assembled and running
satisfactorily.
2. Compare contents of shipping carton with
sect. 5.1 . Report shortages, if any, to your
distributor.
3. Remove four screws holding machine to
shipping pallet.
4. Leave any packing material between vise jaws
and bow intact until band saw has been lifted
to its final position.
5. Use hooks through the lifting rings on the
corners of the saw stand. Make sure straps or
chains are clear of any handles or levers. Lift
machine with forklift or hoist and transport to
desired location. For best performance, the
band saw should be located on a level
concrete foundation. Allow room for servicing
and for moving large stock around the machine
when determining location.
6. Install four screws with hex nuts (provided) into
flanges on base, and over the leveling pads.
Place a level on the table surface and check
side-to-side and front-to-back. Adjust leveling
screws until machine is level in both directions
and tighten nuts.
7. Clean all rust preventative from surfaces with
kerosene or cleaner/degreaser. Do not use
gasoline, paint thinner, mineral spirits, etc., as
these may damage painted surfaces. After
cleaning, apply a light coat of oil to exposed
metal surfaces.
5.3 Lubrication
The band saw is shipped with appropriate levels of
gear and hydraulic oil. The user should verify these
by checking sight glass levels before operating.
Work coolant must be supplied by the operator .
See sect. 10.1.3 for information.
6.0 Electrical connections
Electrical connections must be
made by a qualified electrician in compliance
with all relevant codes. This machine must be
properly grounded while in use to protect the
operator from electrical shock and possible fatal
injury.
The HBS-1220DC band saw is rated at 230V, 3-
phase. It is prewired for 230 volt. Confirm that power
available at the saw’s location matches that for
which the saw is wired.
After wiring, if saw runs backward, disconnect from
power and switch any two of the three power leads.
Before connecting to power source, be sure switch
is in
off position.
6.1 GROUNDING INSTRUCTIONS
Permanently connected tools: This tool should be
connected to a grounded metal permanent wiring
system; or to a system having an equipment-
grounding conductor. Make sure a disconnect is
available for the operator. During hard-wiring of the
machine, make sure the fuses have been removed
or the breakers have been tripped in the circuit to
which the band saw will be connected. ALWAYS
FOLLOW PROPER LOCK-OUT, TAG-OUT
PROCEDURES.
6.2 Converting to 460 volt
The Band Saw is prewired for 230 volt. To change
to 460 volt operation, proceed as follows. Additional
purchases will be required: see electrical box parts
list for any part numbers to order.
1. Open main motor junction box cover, and
change leads based on wiring diagram inside
cover. This diagram is also shown in Figure 6-
1. (Note: In case of discrepancy, diagram inside
junction box cover takes precedence.) Reinstall
cover.
2. Remove oil pump motor junction box cover, and
change incoming leads for oil pump, based on
diagram shown in Figure 6-2. Reinstall cover.
3. Remove coolant pump motor junction box
cover, and change incoming leads for coolant
pump, based on diagram shown in Figure 6-3.
Reinstall cover.
4. Open the electrical box.