Jet 718200K Скачать руководство пользователя страница 7

Страница: 7 / 32

Setup and Assembly

Contents of Shipping Cartons

Note: Unit shipped in two cartons.

Stand Carton

1 Stand with Motor
1 Stand

Door

1 Dust Chute with Mounting Hardware
1 Pedestal Switch with Mounting

Hardware

(JWJ-8HH only)

Main Unit Carton

1 Bed

Assembly

1 Fence

Assembly

1 Cutterhead

Guard

1 Belt

Guard

2 V-Belts
2 Handwheels with handle
1 Fence

Handle

3  Mounting Bolts
3  3/8" Lock Washers
1  Operating Instructions and Parts

Manual

1 Warranty

Card

Tools Included with JWJ-8CS

1   12/14mm Open End Wrench
1  8/10mm Open End Wrench
3  Hex Wrenches (3, 4 and 5 mm)
1 Knife

Gauge

Assembly

Tools included with JWJ-8HH

1   12/14mm Open End Wrench
1  8/10mm Open End Wrench
4  Hex Wrenches (3, 4, 5, 6 mm)
2   Star Point Screwdrivers
5 Knife

Inserts

10 Knife Insert Screws

Tools Required for Assembly:

#1 Cross Point Screwdriver
6-8” Adjustable Wrench or 17 & 19mm

Wrench

Unpacking and Cleanup

1. Carefully finish removing all contents

from both shipping cartons. Compare
contents of the shipping cartons with
the list of contents above. Place parts
on a protected surface.

2. Set packing material and shipping

cartons to the side. Do not discard until
machine has been set up and is
running properly.

3. Clean all rust protected surfaces (bed,

fence, etc.) with kerosene or diesel oil.

Содержание 718200K

































Результаты поиска

Содержание 718200K

Отзывы:

Похожие инструкции для 718200K

Бренды по названию

Популярные бренды

Jet 718200K, Инструкция по эксплуатации и каталог запасных частей

Результаты поиска

Содержание 718200K

Отзывы:

Похожие инструкции для 718200K

Бренды по названию

Популярные бренды