Jet 718200K Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 32

background image

5

27. Do not stand on the machine. Serious injury could occur if the machine tips over.

28. Never leave the machine running unattended. Turn the power off and do not leave the machine until it

comes to a complete stop.

29. Remove loose items and unnecessary work pieces from the area before starting the machine.

Familiarize yourself with the following safety notices used in this manual:

This means that if precautions are not heeded, it may result in minor injury and/or

possible machine damage.

This means that if precautions are not heeded, it may result in serious injury or possibly

even death.

Introduction

This manual is provided by JET covering the safe operation and maintenance procedures for the JET
Model JWJ-8CS and JWJ-8HH Woodworking Jointers. This manual contains instructions on installation,
safety precautions, general operating procedures, maintenance instructions and parts breakdown. This
machine has been designed and constructed to provide consistent, long-term operation if used in
accordance with instructions set forth in this manual. If there are any questions or comments, please
contact either your local supplier or JET. JET can also be reached at our web site: www.jettools.com.

WARNING:

Drilling, sawing, sanding or machining wood products generates wood dust and other

substances known to the State of California to cause cancer. Avoid inhaling dust generated from wood
products or use a dust mask or other safeguards for personal protection.

Wood products emit chemicals known to the State of California to cause birth defects or other
reproductive harm. For more information go to http://www.p65warnings.ca.gov/wood.

WARNING:

This product can expose you to chemicals including titanium dioxide which is known to

the State of California to cause cancer, and lead which is known to the State of California to cause
cancer and birth defects or other reproductive harm. For more information go to http://www.
p65warnings.ca.gov.

«
...
3
4
5
6
7
...
»

Содержание 718200K

































Отзывы:

Нет отзывов

Похожие инструкции для 718200K

Бренд: KaVo Страницы: 10

Бренд: TDK-Lambda Страницы: 29

Бренд: TE Connectivity Страницы: 7

Бренд: Wacker Neuson Страницы: 62

Бренд: Wacker Neuson Страницы: 22

Бренд: Earlex Страницы: 5

Бренд: Everwin Страницы: 12

FATMAX SFMCS650

Бренд: Stanley Страницы: 12

Бренд: M7 Страницы: 17

Бренд: Promaker Страницы: 24

Бренд: jbc Страницы: 8

Бренд: UCAN Страницы: 22

Бренд: Fein Страницы: 53

Бренд: King Canada Страницы: 5

Бренд: Eriez Страницы: 12

Бренд: Echo Страницы: 24

Бренд: BGS technic Страницы: 12

Бренд: Baileigh Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды