Jet-tech 727 Скачать руководство пользователя страница 26

TROUBLE SHOOTING 

 

PROBLEM 

CHECK 

ACTION 

Does not wash properly 

A001 

Is the wash water clean? 

Drain the tank, rinse and refill 

 

 

A002 

Are the wash/rinse arm jets clogged?  Clean the jets/nozzles. Be careful not 

to lose the o -rings. 

 
 

A003 

Are the scrap screens clean? 

Clean the scrap screens  & filters. 

 

 

A004 

Is the water level in the wash tank 
correct? 

Water level should be just under the 
opening of the overflow pipe. 

 

A005 

The air trap may have dirt in it. 

Clean the air trap 

 

 

A006 

The air pressure switch may be faulty.  Adjust or replace as required. 

 
 

A007 

The solenoid valve may have dirt in it 
or may be defective. 

Clean filter or replace as required. 

 

 

A008 

Incoming water pressure may be 
either too low or too high will result in 
poor rinsing. 

If the pressure is too low (under 
25psi), check that the faucet is fully 
opened. If it is, the customer may 
need to install a pressure-booster 
pump to increase the water pressure. 
If the water pressure is too high 
(above 35psi), you must install a 
pressure-reducing valve & set at 
30psi. 

 
 

A009 

Drain outlet hose may be blocked. 
Drain pump may be blocked or 
defective not allowing proper 
drainage of machine. 

Un-clog or reposition hose. Un-clog or 
replace drain pump, as required. 

 

 

A010 

The overflow pipe may be clogged. 

Clean out any residue. 

 

 

A011 

Wash pump may be clogged or 
defective. 

Open face plate of wash pump for 
inspection. Clean wash pump or 
replace it if necessary.  

 

 

A012 

Detergent system may be defective.  Peristaltic hose(s) may have to be 

replaced. The detergent filter in the 
container may be clogged or worn. 
Replace. Check the detergent line for 
deposits. Clean the line if necessary.  

 
 

A013 

Detergent dispenser may be 
defective. 

Replace 

 

 

A014 

The detergent used is of poor quality.   Replace with a q uality commercial 

brand. 

 

 

A015 

Dishes appear dirty after the cycle is 
completed. 

Pre-rinse the dishes properly before 
they are placed into the dish racks. 

 

 

A016 

Foreign material may accumulate on 
the scap screens. 

A foreign object such as napkin, may 
be in the wash system. All tubes and 
wash arms should be cleaned. 

 

 

A017 

Small specs remain on glasses after 
rinsing. 

Have water analyzed. May need a 
filtering system; or other product(s). 

 

Содержание 727





























Отзывы: