Jepson HDC 8203E, Руководство по эксплуатации

Страница: 12 / 100

6.5. REMOVING THE RECHARGEABLE
BATTERY
Unlock the rechargeable battery by pressing the
locking lever (See fig. 11) and pull it out of the
battery guide.
CAUTION!! Do not use force to do so.
6.6. INSTALLING THE BLADE
1. Unplug the rechargeable battery for all service
work.
2. Remove any accumulated debris in the guards
and around the spindle. Check the lower
retracting blade guard to ensure that it is in
working order.
3. Clean the inner spindle flange. Orient the
flange so that the correct bore size faces the
blade and place the new blade on the spindle,
making sure that the teeth point forwards. (If
in doubt of the orientation of the blade, refer
to the legend cast into the lower retracting
blade guard) Avoid contact with blade teeth
to prevent personal injury.
4. NOTE: Only use original Jepson Power saw
blades.
5. Place the outer spindle flange on the spindle
with the flat side toward the blade. See fig. 2.
6. Replace and finger- tighten the blade retaining
bolt by turning it clockwise.
7. Push in the blade lock lever and rotate the
spindle by hand until the lock engages the
spindle See fig. 3. Tighten the blade retaining
bolt securely with the provided wrench and
release the spindle lock.
6.7. REMOVING THE BLADE
1. Unplug the rechargeable battery for all service
work.
2. See fig. 3. It is not necessary to remove the
outer blade cover, just leave it in place. Push
in the spindle lock and using the supplied
hex wrench, rotate the blade until the lock
engages the blade spindle.
3. Avoid contact with the blade teeth to prevent
personal injury.
4. While holding the blade lock lever, use the
provided wrench to loosen the blade retaining
bolt. Then remove it and the outer spindle
flange.
5. The blade may now be carefully removed.
6.8. ADJUSTMENT DEPTH OF CUT
Adjust the depth of cut so that the saw blade
protrudes through the thickness of work piece. To
adjust the depth of cut:
1. Unplug the rechargeable battery for all service
work.
2. Lift the depth lock lever at the rear of the saw.
See fig. 4.
3. Raise or lower the saw base until the blade
extends the desired depth below the base.
(See the scale and pointer cast into the main
body casting.)
4. Press the depth lock lever down firmly, locking
the saw in the selected position.
6.9. ADJUSTMENT OF BEVEL ANGLE
To adjust the bevel angle, refer to the bevel gauge
on the base. There are markings for different angles
from 0 to 45 degrees. To adjust the bevel angle:
Loosen the bevel lock knob
( See fig. 5 ) and the smaller knob at the rear. Lift the
bevel lock knob out of the slot and rotate the base
to the desired angle. The most commonly used
angles each have an individual slot. Simply drop the
bevel lock into the slot and tighten. If other angles
are needed, tighten the bevel lock knob to hold at
the desired position. Then tighten the smaller knob
at the rear of the base.
6.10. HOW TO USE THE SIGHTING NOTCH
To aid in free- hand cutting, a sighting notch is
located at the front of the base. See fig. 6. Align
the cutting line on the work piece with the sighting
notch. Make the cut. Use the right-hand notch
(between the two marking dots) for straight cuts
and the left- hand notch (located below the rivet)
for 45- degree bevel cuts.
6.11. STARTING AND STOPPING TOOL
Do not press the trigger switch before or while
inserting the rechargeable battery. To start the
machine, first press the safety lock button then
squeeze the trigger switch to start the motor.
Release the trigger switch to stop the motor. See
fig. 7.
6.12. REMOVING CHIPS
This dry-cut metal saw has an internal chip collector.
When the chip collector is full, the chips
ENGLISH
12