Jensen JKRS3 Скачать руководство пользователя страница 4

128-7052

4 of 16

Failure to connect this wire to the ignition switch side of the neutral safety switch can result in personal injury and
property damage.
SEE NEUTRAL START SAFETY TEST FOR FURTHER DETAILS.

BLUE WIRE: 

Ignition 1 Output

Connect this wire to the ignition 1 wire from the ignition switch.  This wire will show +12 volts when the ignition key
is turned to the to the "ON" or "RUN" and the "START" or CRANK" positions and will have 0 volts when the key is turned
to the "OFF" and "ACCESSORY" positions.
For Diesel Applications, this wire must be connected to the ignition circuit that powers the glow plugs if the vehicle
requires glow plug pre-heating.

GREEN WIRE: 

Ignition 2 Output

Connect this wire to the ignition 2 wire from the ignition switch.  This wire will show + 12 volts when the ignition key
is turned to the "ON" or "RUN" position and is some cases the "START" or CRANK" position.  This wire will show 0
volts when the key is turned to the "OFF" and "ACCESSORY" positions.
NOTE: See programming information concerning this wire to allow output during the "START" mode.

VIOLET WIRE:

 Accessory Output

Connect this wire to the Accessory wire from the ignition switch.  This wire will show + 12 volts when the ignition
switch is turned to the  "ACCESSORY" or "ON" and "RUN" positions and will show 0 volts when the key is turned to
the "OFF" and "START" or "CRANK" positions.

4

Содержание JKRS3

















Отзывы: