Jensen DT-985 Скачать руководство пользователя страница 14

Страница: 14 / 14

Enclosure

Double molded

Shock (Drop Test)

6.5 feet

(2 meters)

Diode Test

Test current of 1.5mA maximum, open circuit voltage 3V DC typical

Continuity Check

Audible signal will sound if the resistance is less than 50



(approx.),

test current <0.35mA

Temperature Sensor

Requires type K thermocouple

Input Impedance

>10MΩ VDC & >10MΩ VAC

AC Response

Averaging

ACV Bandwidth

50/60HZ(ALL WAVE)

45Hz to 1000Hz(SINE WAVE)

Crest Factor

≤3 at full scale up to 500V, decreasing linearly to ≤1.5 at 1000V

Display

6,000 counts

Overrange indication

“

” is displayed

Auto Power Off

30minutes (approximately) with disable feature

Polarity

Automatic (no indication for positive); Minus (-) sign for negative

Measurement Rate 3

times per second, nominal

Low Battery Indication

“

”

is displayed if battery voltage drops below operating

voltage

Battery

1.5VAAA *4 battery

Fuses

mA, µA ranges; 0.8A/1000V ceramic fast blow

A range; 10A/1000V ceramic fast blow

Operating Temperature



F to 104



F (5



C to 40



Storage Temperature

-4



F to 140



F (-20



C to 60



Operating Humidity

Max 80% up to 87



F (31



C) decreasing linearly to 50% at 104



(40



Storage Humidity

<80%

Operating Altitude

7000ft. (2000meters) maximum.

Weight

0.753lb (342g) (includes holster).

Size

(182x 82 x 59mm) (includes holster)

Safety

This

meter is intended for origin of installation use and protected, against the users, by double
insulation per EN61010-1 and IEC61010-1 2

Edition (2001) to Category IV 600V and

Category III 1000V; Pollution Degree 2. The meter also meets UL 61010-1, 2

Edition

(2004), CAN/CSA C22.2 No. 61010-1 2

Edition (2004), and UL 61010-2-033, 1

Edition

(2012)

Содержание DT-985















Результаты поиска

Содержание DT-985

Отзывы:

Похожие инструкции для DT-985

Бренды по названию

Популярные бренды

Jensen DT-985, Руководство пользователя

Результаты поиска

Содержание DT-985

Отзывы:

Похожие инструкции для DT-985

Бренды по названию

Популярные бренды