background image

7

®

CD615X

Wiring Diagram–Advanced Installation

If you are installing new speakers or amplifiers or replacing an aftermarket installation, use this diagram.

Fuses

When replacing a fuse, make sure new
fuse is correct type and amperage. Using
an incorrect fuse could damage radio. The
CD615X uses two fuses with in-line fuse
holders as part of rear wiring harness:

• 10 amp fast blow AGC (yellow wire)

• 2 amp fast blow AGC (red wire)

• 2 amp fast blow AGC (orange wire)

Memory
Connect to battery or 12 volt power
source that is always live.

The radio will not work if this wire
is not connected.

Accessory
Connect to existing radio wire or
radio fuse.

Ground
Connect to ground terminal or clean,
unpainted metal part of chassis.

Power Antenna
Connect to power antenna or
amplifier. If not used, tape bare
end of wire.

Go to “Testing” on page 8.

Dimmer
Connect to existing dimmer wire.

LF

LR

RF

RR

AMP

+

AMP

Filter

Box

Red

White

Antenna 

adapter for

GM cars

(not supplied)

Antenna

jack

Antenna

extender

cable

(not supplied)

LF–

white/black

white

LF+

RF–

gray/black

gray
RF+

LR–

green/black

RR–

violet/black

green

LR+

violet

RR+

Black

Yellow

Red

Dark Blue

Amplifier wiring

(See amplifier instructions)

RCA-to-RCA cables

(not supplied)

Orange

In-line

fuse

(2-amp)

In-line

fuse

(2-amp)

In-line

fuse

(10-amp)

5293_Ein.p65

4/10/99, 11:19 PM

7

Содержание CD615X














Отзывы: