Jensen CD510K Скачать руководство пользователя страница 7

Страница: 7 / 13

CD510K

LF–

white/black

white

LF+

RF–

gray/black

gray

RF+

LR–

green/black

green

LR+

RR–

violet/black

violet

RR+

AMP

Amplifier wiring

(See amplifier instructions)

RCA-to-RCA cables

(not supplied)

Sub

Output

–

Black

Yellow

Pink

Red

AMP

Orange

Filter

Box

10-amp fuse

In-line

Fuse

(1-amp)

Antenna

extender

cable (not

supplied)

Optional

CD Changer

Antenna

Jack

Back of Receiver

Dark Blue

In-line

Fuse

(1-amp)

AMP

Amplifier wiring

(See amplifier instructions)

RCA-to-RCA cables

(not supplied)

Wiring Diagram–Advanced Installation

If you are installing new speakers or amplifiers or replacing an aftermarket installation, use this diagram.

Fuses

When replacing a fuse, make sure new
fuse is correct type and amperage. Using
an incorrect fuse could damage radio.
The CD510K uses one 10 amp (in the
filter box) and two 1 amp fast blow AGC
fuses as part of rear wiring harness.

Memory

Connect to battery or 12 volt power
source that is always live.

The radio will not work if this wire
is not connected.

Accessory

Connect to existing radio wire or
radio fuse.

Ground

Connect to ground terminal or clean,
unpainted metal part of chassis.

Power Antenna

Connect to power antenna or
amplifier. If not used, tape bare
end of wire.

Go to “Testing” on page 8.

Cellular Mute

Dimmer

Connect to
existing
dimmer wire

Содержание CD510K














Результаты поиска

Содержание CD510K

Отзывы:

Бренды по названию

Популярные бренды

Jensen CD510K, Руководство по установке

Результаты поиска

Содержание CD510K

Отзывы:

Бренды по названию

Популярные бренды