manualshive.com logo in svg

Jensen CD510K, Руководство по установке

Поделиться
Скачать
Jensen CD510K Скачать руководство пользователя страница 2

2

®

CD510K

Before You Begin Installation

Before you begin, you will need tools, supplies and adapters. It is best to make sure you have
everything you need before you take your dashboard apart.

 Installation

Prepare Radio for Installation

Tools and Supplies Needed

Basic Installation:

• Torx type screwdrivers

• Flat and Phillips screwdrivers

• Wire cutters

• Wire strippers

• Tools to remove existing radio (screw-

driver, socket wrench set or other tools)

• Radio removal tool

• Electrical tape

Advanced Installation:

• Soldering iron

• Crimping tool

• Volt meter/12 volt test light

• Solder

• Crimp connectors

• 18 gauge wire for power connections

• 16-18 gauge speaker wire

Remove transport
screw (you cannot
insert a CD until the
screw is removed)

Put adhesive dot (from
accessory kit) over
transport screw hole

Adapters for Easier Installation

Electrical and dashboard adapters make
installation easier. Purchase adapters from
your local Jensen retailer, electronics store or
car stereo specialty store.

Wiring Harness Adapter

For a basic installation, you can purchase a
wiring harness adapter for your car's existing
radio connectors. This makes installation easy.

Dashboard Adapters

The opening in your dashboard may not match
the  size of your Jensen radio. Purchase an
adapter kit for your car.

Antenna Adapter 

(GM cars)

1990 and newer GM cars have a small
antenna connector. You will need an adapter
when installing this radio in a newer GM car.

Speaker Requirements

Only connect the CD510K to speakers rated in
the load impedance range of 4 to 8 ohms.
Speakers with a load impedance less than 4
ohms could damage the CD510K.

COMP

ACT

DIGITA

L AUD

IO

®

PWR

BND

AS/PS

LOUD

SHIFT

S.WFR

CH

MONO

LOC LOU

D

CDC

0

+

+

S.W

MEM

CLR

6

7

8

9

10

INT

1

RPT

2

3

RDM

4

PGM

CLK

DISP

5

REL

M

OD

E

SE

L

Содержание CD510K














Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды