background image

14

Care and Cleaning

Cleaning

Light Bulb Replacement

Condenser:

The condenser tubing inside the wine

chiller does not require frequent cleaning; however,
satisfactory cooling depends on adequate ventilation
over the coils.  Be sure that nothing obstructs the
required air flow openings in front of the wine chiller.
At least twice a year brush or vacuum lint and dirt
from the condenser for efficient performance by
unscrewing the grille on the bottom front of the wine
chiller.

Wine Chiller:

The painted cabinet can be washed

with mild detergent and water and thoroughly rinsed
with clear water.  Never use abrasive scouring
powders.

Stainless Steel Door Frame:

Use a soft cloth or

sponge and wipe with the grain of the stainless steel.
Use mild detergent and water for light soil, Bon Ami*
for more moderate soil and Cameo Stainless Steel
Cleaner* for discoloration.  Do not use chlorine
bleach or products containing chlorine bleach on
stainless steel.

After cleaning, rinse and dry.  To restore luster and
remove streaks, follow with Stainless Steel Magic
Spray* (Jenn-Air model A912, part number
20000008).

Interior:

Wash interior compartment with mild

detergent and water.  Do not use an abrasive
powder, solvent, polish cleaner or undiluted
detergent.

Glass Door:

Use a glass cleaner or mild detergent

and water and soft cloth to clean the glass door.  Do
not use abrasive powders.

Door Gasket:

The vinyl gasket may be cleaned 

with mild detergent and water, or a solution of 
2 tablespoons baking soda to 1 quart warm water.

The wine chiller uses a 15 watt, intermediate base bulb
and is located inside the light shield.  The light shield is
on the ceiling of the wine chiller and is held in place by
three screws.  Remove the three screws and light
shield to remove the light bulb.  Do not use a
replacement light bulb greater than 15 watts.

In the Event of a Power Failure

If the power fails, open the door as infrequently as
possible to maintain the temperature.  A gradual rise in
temperature should not have any adverse effect on the
wine. 

If it is extremely hot, you may want to move the wine to
the coolest location you can find until power is
restored.

* Brand names for cleaning products are registered trademarks of the respective manufacturers.

To avoid personal injury or property damage,
observe the following:

• Allow light bulb to cool.

• Wear gloves when replacing light bulb.

CAUTION

• To avoid electrical shock which can cause severe

personal injury or death, disconnect power to the
wine chiller before cleaning.

WARNING

• To avoid electrical shock which can cause severe

personal injury or death, disconnect power to the
wine chiller before replacing light bulb.  After
replacing light bulb, connect power.

WARNING

Содержание JWC2450ARB





















































Отзывы: