Jenn-Air JDS8850AAB, Руководство по обслуживанию

Страница: 19 / 62

Testing Procedures
!
WARNING
To avoid risk of electrical shock, personal injury or death; disconnect power and gas to oven before servicing,
unless testing requires power and/or gas.
©2005 Maytag Services
16026016 19
!
WARNING
To avoid risk of electrical shock, personal injury or equipment failure, use extreme caution when taking voltage
measurements in the Electronic Control. Failure to do so could short-circuit the control or result in electrical shock.
Illustration Component Test Procedure Results
Electronic control Door logic sensor ..............................
Meat probe ........................................
Downdraft motor high setting.............
Downdraft motor low setting .............. P11 (Red, pin 5) to P11 (Black,
pin 2):
Door
Locked: Continuity
Door Unlocked: Infinity
P2 (Red) to P2 (Red). See
"
Meat
Probe
"
chart.
P14 (Tan) to P5 (White): 120 VAC
P22 (Orange) to P5 (White): 120 VAC
Oven Control Testing Procedures
Changing factory set default options: 1. Press
Setup Options
and the desired pad simultaneously (see table).
2. Press Autoset to change the option.
3. Press any pad except Cancel to accept the change.
4. Press
Cancel
to cancel the operation.
Control Component Test Procedure Results
EOC II Oven
temperature
adjustment Press Bake pad and enter 550° F (288° C).
Press and hold Bake pad until TEMP ADJ
displays. Press Autoset pad to adjust oven in
5° F (-15° C) increments, from -35° F
(-37° C) to 35° F (2° C).
While increasing or decreasing oven
temperature, this does not affect self-
cleaning temperature.
EOC II End-of-Timer
Reminder beeps Press
Setup Options
and the applicable timer
pad ( Timer 1 or Timer 2 ) simultaneously.
Selects the number of beeps emitted
when a timed bake cycle ends.
EOC II Control Lock Press Setup Options and the Control Lock pad
(also the 1 pad) simultaneously.
Press Autoset to select option (enable
disable). The timer, clock and oven light
remain operational.
EOC II Twelve Hour off/
Sabbath mode Press
Setup Options
and the
12 Hour Off
pad
(also the 2 pad) simultaneously.
Disables the normal 12-hour shutoff,
allowing the oven to operate indefinitely.
EOC II Sound Level
(Beeper Volume) Press Setup Options and the Sound Level pad
(also the 3 pad) simultaneously.
Press Autoset to select setting (I lowest
through IIIIIIII 8 highest).
EOC II 24-Hour Clock Press Setup Options and the 12/24 Hour Clock
pad (also the
4
pad) simultaneously.
Press Autoset to select option (12-hour
time or 24-hour time).
EOC II Scroll Speed Press Setup Options and the Scroll Speed pad
(also the 5 pad) simultaneously.
Press Autoset to set speed of displayed
messages (slow, medium, fast).
EOC II End-of-Cook-
Time Signal Press Setup Options and Cook Time Beeps
pads (also the 6 pad) simultaneously.
Press Autoset to set the number of
beeps emitted at the end of a " clock-
controlled
"
cook cycle.
EOC II Temperature
Display Press Setup Options and the Temp C/F pad
(also the
7
pad) simultaneously.
Press Autoset to select option
(°F or °C).
EOC II Language
Display Press Setup Options and the Language pad
(also the 8 pad) simultaneously.
Press Autoset to select option
(English, French or Spanish).
EOC II Factory Default
Press Setup Options and the Default pad (also
the 9 pad) simultaneously.
Press Autoset to reset clock to factory
settings.
EOC II Clock Display Press
Setup Options
and the
Display On/Off
pad (also the Clock pad) simultaneously.
Press
Autoset
to select clock display (on
or off).
EOC II Test Access Press and hold Cancel and Broil pads for 3
seconds at power up or within 5 minutes of
power up mode. See "Quick Test Mode."
Allows access to each function for testing
purposes.