Jenn-Air JDD4000AWS, Инструкция пользователя

Страница: 6 / 24

6
Dishwasher Features
Your Jenn-Air ® dishwasher may have some or all of these features.
Removable Rack Insert
Each drawer has one
removable rack insert
which allows you to
adjust the rack to the
type of load you are
washing.
To install rack insert:
1.
Place the insert end legs under the back base rack wire.
2. Gently push down on the insert rack handle until the insert
locks into position.
To remove rack
insert:
Gently pull in and up
on the handle to
release the insert
handle from the base
rack.
Sabbath Guidelines (on some models)
For those who observe kosher dietary guidelines, Star-K has
certified that the drawers in the 2-drawer model are separate and
therefore one drawer can be designated to wash utensils used for
dairy, while the other can be designated for washing meat utensils.
However, neither drawer can be used to wash dishes on the
Sabbath or holidays.
Storage of dishes
Although washing of dishes with the drawer dishwasher is not
permitted on the Sabbath or on holidays, storage of dishes is
possible by following the guidelines listed below.
IMPORTANT: Attention should be paid when opening the drawer(s)
and loading dishes while in the disabled mode as an unintended
key press could activate the indicator lights.
Turning off the Rinse Aid Low Indicator light:
To turn off the Rinse Aid Low indicator light, set the Rinse Aid
Dispenser level to “0.” See “Rinse Aid Adjustment Mode.”
To deactivate the tones, see “Tone Option Adjustment Mode.”
If the Child Lock feature has been set, deactivate during the
Sabbath or holidays.
To return to normal operation:
To reactivate your desired rinse aid level, see “Rinse Aid
Adjustment Mode.” To reactivate your desired tones, see “Tone
Option Adjustment Mode.”
NOTES:
■ If needed, be sure to allow enough time to run a cleaning cycle
prior to the start of the Sabbath.
■ Clean dishes should be unloaded from the drawer dishwasher
prior to setting the controls for the Sabbath to avoid activation
of the indicator lights.
Rinse Aid Adjustment Mode
NOTE:
The rinse aid cannot be adjusted while a cycle is running.
To enter the Rinse Aid Adjustment Mode:
1. Press and hold the SUPER SCRUB option pad for 3 seconds.
A tone will sound to indicate you have entered the Rinse Aid
Adjustment Mode.
2. The rinse aid dispenser has 4 settings. “0” is the lowest with
no rinse aid being dispensed and “3” the highest setting. With
each consecutive press of the Super Scrub option pad, the
amount of rinse aid being dispensed into the dishwasher
drawers increases.
3. Cycle lights illuminate with each touch of the Super Scrub
option to indicate which rinse aid level is selected. See table.
NOTE: A rinse aid dispenser level of “0” disables the Rinse-Aid
Low indicator light.
To exit the Rinse Aid Adjustment Mode:
Press any key other than Super Scrub to exit the Rinse Aid
Adjustment Mode.
Tone Option Adjustment Mode
1.
Press and hold SUPER SCRUB for 3 seconds. A tone will
sound to indicate you have entered the Tone Option
Adjustment Mode.
2. To change the tone options, press 6 HOUR DELAY.
3. Each press of the 6 Hour Delay pad will move through each
available setting. Continue to press the 6 Hour Delay until
reaching the desired tone option. See table.
4. Press any key other than 6 Hour Delay to exit the Tone Option
Adjustment Mode.
A. Large insert
B. Base rack
A
B
RINSE AID
DISPENSER
LEVEL
0 OFF OFF OFF
1 ON OFF OFF
2 ON ON OFF
3 ON ON ON
TONE OPTIONS STATUS INDICATOR LIGHTS
Sanitized/
Clean Rinse Aid Low
Drawer open/button press/
End-of-cycle chime disabled OFF OFF
Drawer open chime enabled ON OFF
Drawer open/button press
chime enabled OFF ON
Drawer open/button press
End-of-cycle chime enabled ON ON