12
2.
Connect the flexible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve as shown.
3.
Place the end of the tubing into a bucket, and turn shutoff
valve ON.
4.
Check for leaks. Tighten any nuts or connections (including
connections at the valve) that leak.
Style 2—Copper Line Connection
NOTE:
If there is a water supply line that meets the specifications
in “Water Supply Requirements,” proceed to “Connecting to
Refrigerator.” If not, use the following instructions to connect to
the household cold water supply.
1.
Unplug refrigerator or disconnect power.
2.
Turn OFF main water supply. Turn ON nearest faucet long
enough to clear line of water.
3.
Locate a 1/2" to 1¹⁄
4
" (1.3 cm to 3.18 cm) vertical cold water
pipe near the refrigerator.
IMPORTANT:
■
Make sure it is a cold water pipe.
■
Horizontal pipe will work, but drill on the top side of the
pipe, not the bottom. This will help keep water away from
the drill and keep normal sediment from collecting in the
valve.
4.
Determine the length of copper tubing you need. Measure
from the connection on the refrigerator to the water pipe.
Add 7 ft (2.1 m) to allow for cleaning. Use 1/4" (6.35 mm)
O.D. (outside diameter) copper tubing. Be sure both ends of
copper tubing are cut square.
5.
Using a cordless drill, drill a 1/4" (6.35 mm) hole in the cold
water pipe you have selected.
6.
Fasten the shutoff valve to the cold water pipe with the pipe
clamp. Be sure the outlet end is solidly in the 1/4" (6.35 mm)
drilled hole in the water pipe and that the washer is under the
pipe clamp. Tighten the packing nut. Tighten the pipe clamp
screws slowly and evenly so washer makes a watertight seal.
Do not overtighten.
IMPORTANT:
Before attaching the tubing to shutoff valve, flush
the main water supply line to remove particles and air in the water
line. Allow enough flow so that water becomes clear. Flushing
the water line may help avoid filters and/or water valves from
becoming clogged.
7.
Slip the compression sleeve and compression nut on the
copper tubing as shown. Insert the end of the tubing into the
outlet end squarely as far as it will go. Screw compression nut
onto outlet end with adjustable wrench. Do not overtighten
the clamp or the sleeve. This will crush the copper tubing.
8.
Turn off the shutoff valve on the water pipe. Coil the copper
tubing.
9.
Connect the flexible, codes-approved water supply line to the
water shutoff valve by threading the provided nut onto the
shutoff valve.
10.
Place the end of the tubing into a bucket, and turn shutoff
valve ON.
11.
Check for leaks around the saddle valve. Tighten any nuts or
connections (including connections at the valve) that leak.
Connect to Refrigerator
Parts Supplied
■
1/4" to 1/4" (6.35 mm to 6.35 mm) male-to-male coupling (on
some models)
NOTE:
The flexible, codes-approved water supply line should
connect to the supply valve through the floor.
1.
Unplug the refrigerator or disconnect power.
2.
Connect the 7 ft (2.13 m) flexible codes-approved water tube
to the water supply valve.
3.
Flush the main water supply line to remove particles and air in
the water line. Allow enough flow so that water becomes clear
4.
Tape the 7 ft (2.13 m) flexible codes-approved water supply
line to the floor, 7" (17.78 cm) from the left side of the
refrigerator. Tape along the length of the tubing, which will
allow it to pass beneath the refrigerator without interference.
NOTE:
Allow a minimum of 26" (66.04 cm) of flexible codes-
approved water supply line to be loose at the front of the
refrigerator for connecting to the refrigerator.
A
B
C
A. Bulb
B. Nut
C. Water tubing
A
B
C
D
E
F
G
A. Cold water pipe
B. Pipe clamp
C. Copper tubing
D. Compression nut
E. Compression sleeve
F. Shutoff valve
G. Packing nut
6"
(15.2 cm)
6"
(15.2 cm)
1"
(2.54 cm)
7"
(17.78 cm)
