4
Cabinet Dimensions
*NOTE: Grills installed near a side wall must allow a minimum
clearance of 6" (15.2 cm) between cooktop and sidewall for
maximum performance. Minimum clearance of 1" (2.5 cm) is
required to sidewalls and ¾" (1.9 cm) to rear wall.
NOTES: After making the countertop cutout, some installations
may require notching down the base cabinet side walls to clear
the cooktop base. To avoid this modification, use a base cabinet
with sidewalls wider than the cutout.
■
Where possible, a 6" (15.2 cm) clearance is recommended for
motor blower service. A minimum clearance of 1" (2.5 cm) is
recommended to the sidewalls and a
³⁄₄
" (1.9 cm) clearance is
recommended to the rear wall.
■
A minimum clearance of
2
" (5.1 cm) is recommended
between the motor/blower and cabinet for proper cooling.
■
A minimum clearance of
6¹⁄₄
" (15.9 cm) is recommended for
removal of the grease container(s). Installed dimension for the
grease containers is 5
¹⁄₂
" (14.0 cm).
■
For grills installed near a sidewall, a minimum clearance of
6
" (15.2 cm) is recommended between the cooktop and
sidewall for maximum performance.
Cutout Dimensions
Venting Requirements
■
Do not terminate the vent system in an attic or other enclosed
area.
■
Use a Jenn-Air
®
vent cap.
■
Vent system must terminate to the outside.
■
Use only a 6" (15.2 cm) round metal vent. Rigid metal vent is
recommended. For best performance, do not use plastic or
metal foil vent.
■
Before making cutouts, make sure there is proper clearance
within the wall or floor for the exhaust vent.
■
Do not cut a joist or stud unless absolutely necessary. If a
joist or stud must be cut, then a supporting frame must be
constructed.
■
The size of the vent should be uniform.
■
The vent system must have a damper. If roof or wall cap has a
damper, do not use damper supplied with the range hood.
A. 24" (61.0 cm) on 20" (50.8 cm) single cartridge models
30" (76.2 cm) on 30" (76.2 cm) double cartridge models
43" (109.2 cm) on 43" (109.2 cm) triple cartridge models
B. Combustible area above countertop (shown by dashed box above)
C. 30" (76.2 cm) minimum clearance between top of cooktop platform
and bottom of uncovered wood or metal cabinet (24" [61 cm]
minimum clearance if bottom of wood or metal cabinet is covered
by not less than
¹⁄₄
" [0.6 cm] flame retardant millboard covered with
not less than No. 28 MSG sheet steel, 0.015" [0.04 cm] stainless
steel, or 0.024" [0.06 cm] aluminum or 0.020" [0.05 cm] copper)
D. 13" (33 cm) recommended upper cabinet depth
E. 2
¹⁄₈
" (5.4 cm) min.
F. 20
⁹⁄₁₆
" (58.2 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to countertop
within minimum horizontal clearances to cooktop
H. Junction box or outlet; 12" (30.5 cm) minimum from bottom of
countertop
I. Junction box or outlet; 10" (25.4 cm) from right-hand side of
cabinet
J. 18
¹¹⁄₁₆
" (47.5 cm) on 20" (50.8 cm) single cartridge models
30
⁷⁄₁₆
" (77.3 cm) on 30" (76.2 cm) double cartridge models
41
³¹⁄₃₂
" (106.6 cm) on 43" (109.2 cm) triple cartridge models
K. Side clearance - See *NOTE.
L. 2" (5.1 cm) minimum clearance between back wall and countertop
cutout
D
A
E
I
J
K
G
H
L
C
F
B
A. 18
¹¹⁄₁₆
" ±
¹⁄₁₆
" (47.5 cm ± 0.2 cm) on 20" (50.8 cm) single cartridge
models
30
⁷⁄₁₆
" ±
¹⁄₁₆
" (77.3 cm ± 0.2 cm) on 30" (76.2 cm) double cartridge
models
41
³¹⁄₃₂
" ±
¹⁄₁₆
" (106.6 cm ± 0.2 cm) on 43" (109.2 cm) triple
cartridge models
B. 20
⁹⁄₁₆
" ±
¹⁄₁₆
" (52.2 cm ± 0.2 cm) maximum on all models
C. 6
⁵⁄₁₆
" (16.0 cm) on 20" (50.8 cm) single cartridge models
17¾" (45.1 cm) on 30" (76.2 cm) double cartridge models
17¾" (45.1 cm) on 43" (109.2 cm) triple cartridge models
D. 14
⁷⁄₁₆
" (36.7 cm) on all models
E. 2
¹⁄₈
" (5.4 cm) minimum space to front edge of cooktop
F. Minimum cabinet width:
21" (53.3 cm) on 20" (50.8 cm) single cartridge models
33" (83.8 cm) on 30" (76.2 cm) double cartridge models
43" (109.2 cm) on 43" (109.2 cm) triple cartridge models
G. Floor exhaust option
H. 6
¹⁄₈
" (15.6 cm) for 6" vent system
I. 6
⁵⁄₁₆
" (16.0 cm) on 20" (50.8 cm) single cartridge models
17¾" (45.1 cm) on 30" (76.2 cm) double cartridge models
17¾" (45.1 cm) on 43" (109.2 cm) triple cartridge models
J. 8" (20.3 cm) from center of the vent hole in the cabinet to the top
surface of the countertop, on all models
K. Wall exhaust option
A
B
C
D
E
G
H
I
J
K
F
