JEM AF-2 Скачать руководство пользователя страница 15

Страница: 15 / 27

Refitting

8. Fit new

DMX

PCB

to the

MOUNTING PLATE

using the screws through the XLR sockets.

9. Ensure that the

RED LED

lines up with the hole in the chassis.

10. Reconnect the

DMX

PCB

WIRING

LOOMS

(Observe polarity).

11.  Check the operation of the unit and adjust if necessary.
12.  Refit the
13.  Refit the

TOP

COVER

How To Upgrade The Software:

1. Using the

SOFTWARE

provided with the

EPSILON 5 PROGRAMMER

upload the latest

SOFTWARE VERSION

(which is available for free from our

WEBSITE

) onto the

EPSILON 5

PROGRAMMER.

2. Disconnect the

PROGRAMMER

from your

3. Remove the

BOTTOM COVER

of the machine.

4. Plug the

WAY

HEADER

into the

AVR

PORT

on the

MAIN PCB

of the machine.

5. Apply power to the machine.
6. Check that the ‘

POWER’

LED

on the

PROGRAMMER

comes on.

7. On the

PROGRAMMER

, press the ‘

NO’

button once to clear the fail indicator.

8. Press the

'YES'

button.

9. Wait for the

'BUSY'

LED

to go out.

10. When the

PROGRAMMER

shows

'PASS'

, press

'NO'

, and then disconnect the machine

from power.

11. Unplug the

PROGRAMMER

12. Apply power to the machine and check the operation of the machine.

Содержание AF-2




























Результаты поиска

Содержание AF-2

Отзывы:

Похожие инструкции для AF-2

Бренды по названию

Популярные бренды

JEM AF-2, Руководство по обслуживанию

Результаты поиска

Содержание AF-2

Отзывы:

Похожие инструкции для AF-2

Бренды по названию

Популярные бренды