JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36 Скачать руководство пользователя страница 33

Страница: 33 / 33

WWW.JEIUK.COM

RAILBEAST RDP-36

This document is protected by copyrights.

Copying, using, or distributing without permission of Ansa Group Ltd is prohibited.

7. WARRANTY CARD

WARRANTY CARD No

.............

..................................................................... in the name of Manufacturer warrants the

RAILBEAST RDP-36 Petrol Rail Drilling Machine to be free of defects in material and

workmanship under normal use for a period of 12 months from the date of sale.

This warranty does not cover tools, Honda GXH50 engine, and damage or wear

that arise from misuse, accident, tempering or any other causes not related to defects

in workmanship or material.

Date of production .........................................................................................................

Serial number ................................................................................................................

Date of sale ...................................................................................................................

Signature of seller ..........................................................................................................

1.02 / 15 November 2017

WE RESERVE THE RIGHT TO MAKE CHANGES IN THIS MANUAL WITHOUT NOTICE

Содержание RAILBEAST RDP-36


































Результаты поиска

Содержание RAILBEAST RDP-36

Отзывы:

Бренды по названию

Популярные бренды

JEI DRILLING & CUTTING SOLUTIONS RAILBEAST RDP-36, Руководство оператора

Результаты поиска

Содержание RAILBEAST RDP-36

Отзывы:

Бренды по названию

Популярные бренды